User manual TOSHIBA V1100

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. [. . . ] This function automatically selects paper that is the same size as the original placed in the ADF, or the same size as that selected with the [ORIGINAL SIZE ENTER] key ( ) The function can be disabled. If the paper runs out during printing and there is paper of the same size and orientation in another tray, this function automatically switches to that tray (excluding the bypass tray). See "AUDITING MODE SETTINGS" (p. 36). 4 the ADF is installed. *2 On model with the two trays. 33 USER SETTINGS Program number Program name Setting codes (factory default setting appears in bold) 1: 300 dpi 2: 600 dpi Explanation · This setting is used to change the copy 23 Resolution in Auto/Text mode 25 Key auto repeat 0: OFF 1: ON resolution in AUTO and TEXT mode from 600 x 300 dpi to 600 x 600 dpi (high-quality mode). Scanning is slower when high-quality mode is used. · Use this setting to select whether or not holding down a key causes repeated input of the key. For keys that normally cause a set value to increase when held down (for example, holding down the [ZOOM] key ( , )), this program can be used to have the set value not change when the key is held down. · Use this setting to select how long a key must 26 Key press time 27 28 29 Audible signals volume Base setting beep signal Number of copies limit 1: Minimum (current response speed) 2: 0. 5 sec. 1: Long beep 2: Short beep 3: OFF 0: OFF 1: ON 1: 99 copies 2: 999 copies 0: OFF 1: ON 1: Upper paper tray*3 2: Lower paper tray*3 5: Bypass tray*3 1: AUTO 2: TEXT 3: PHOTO be pressed for the input to be accepted. By selecting a longer time, you can prevent settings from being changed by the accidental pressing of a key. · This sets the volume of beep signals. (p. 35) · Use this to sound a beep when a base setting 30 Use close paper size 31 Default tray setting is selected. (p. 35) · Use this setting to select 99 or 999 for the maximum number of copies. "Auditing mode" is initially disabled. Use to change an account number. 14 15 Use to delete an account number. 0: Delete single account A single account number can be deleted, or all 1: Delete all accounts account numbers at once. This displays the number of copies made by each account. If this number is exceeded, the count will start over from 0. Use to reset the copy count of an account to 0. 0: Reset single account The copy count of a single account or of all 1: Reset all accounts accounts can be reset. 36 USER SETTINGS SELECTING AUDITING MODE SETTINGS 1 Hold down the [Light] key ( the alarm indicators ( , , blink. , ) until , ) The display shows "- -" with the left hyphen blinking. 2 Enter the program number with the numeric keys. · See "AUDITING MODE SETTINGS" (p. 36) for the program numbers. · The selected program number blinks. · For example, to select "Auditing mode", enter "10". Note If you enter the wrong number, press the [CLEAR] key ( ) and then enter the correct number. 4 3 Press the [START] key ( ). · The selected program number stops blinking and lights steadily. · The currently selected setting code blinks on the right side of the display. 4 Enter the desired setting code for the program as explained in the detailed procedures on the following pages. For the setting codes, see "AUDITING MODE SETTINGS" (p. 36). Note If you enter the wrong number, press the [CLEAR] key ( ) and return to step 2. [. . . ] 18 Original, placing - Document cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 - ADF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Tray selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Two-sided copies using bypass tray . . . . . . . . . . . . . . . . . . . . . . . [. . . ]