User manual TOSHIBA W727

[. . . ] SQPB Video Cassette Recorder W-727 OWNER'S MANUAL ABLE BOX ONTROL 3 SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] · Make sure that the clock is set correctly (page 15). · Store the channels on the VCR (pages 16 and 17). · If you record cable channels, finish the cable box set-up (pages 32-35), and turn on the cable box . · If you record satellite channels, finish the DSS® satellite receiver set-up (pages 36 ­ 38), and turn on the DSS® satellite receiver. Timer Programming Procedure POWER VCR TV CH/TRK 1 4 7 I. SELECT 2 5 8 0 3 6 TV VOL Number buttons Example: To record cable channel 25 in the SP tape speed from 9:20 p. m. Today is August 25. RECORDING 9 100 DISPLAY REMAIN/ COUNTER COUNT RESET TV/ VCR 10 FF PLAY/x2 STOP ENTER 1 2 3 Load a cassette with the safety tab attached. Select "PROGRAM" using FF or REW, and press ENTER. SP/ SLP REC PLAY/x2 TIMER SLOW PAUSE/STILL CURSOR REW STOP FF PROG. CANCEL ENTER CABLE BOX CH VCR Plus+ A. SELECT EJECT CM SKIP POWER REW 4 2, 9 Move to the next using FF, and select the channel number 25 by pressing number buttons 2 and 5, PLAY/x2 or STOP. · To record a cable program from the connected cable box: Enter the cable channel number by number buttons, PLAY/x2 or STOP. If your cable box is not remote-controllable, choose the desired channel (1 to 125) on the cable box. · To record a satellite program from the connected DSS® satellite receiver: Enter the satellite channel number (100 to 999) by number buttons, PLAY/x2 or STOP. (If a number 1 to 99 is entered, the VCR will record a TV/CATV program on the channel, not a satellite's. ) If your DSS® satellite receiver is not remote-controllable, choose the desired channel (100 to 999) on the DSS® satellite receiver. · You can make "L1" or "L2" appear on the channel number position by pressing I. SELECT depending on your connection. To make corrections: Press REW to move back to the item, or FF to forward. (Continued) 25 Timer Program Recording (continued) 5 Move to the next using FF, and set the recording date using PLAY/x2 or STOP. The date changes as follows: 8/25 9/25 . . . MO~FR WKLYSA [WKLYSU]. . . [WKLYSA]: You can record TV programs on the same channel on the day and time every week. [MO~FR]: You can record TV programs on the same channel on the day and time Monday through Friday. 6 Move to the next using FF, and set the hour and minutes of the recording start time. P M 7 Move to the next, and set the recording off time. 8 Move to the next, and select the tape speed (SP) using PLAY/x2 or STOP. For the tape speed "AUTO (Auto Speed Select)", see below. To set another program, press FF, and select the next line pressing STOP. Repeat steps 4 to 8. SP 9 10 Auto Speed Select Press PROG. . Now programming is completed. Press both TIMER simultaneously. The power turns off and the VCR enters the timer standby mode. REC TIMER TIMERHi-Fi STEREO L If you are not sure the tape is long enough for timer program recording in the SP tape speed, set the recording tape speed to "AUTO". Recording starts in the SP tape speed and the VCR automatically selects the tape speed to record the program to the end. If the tape length is not long enough, the tape speed automatically changes from SP to SLP. Notes · Make sure that the tape length is selected correctly according to the tape used on the SET UP screen (page 22). · When the SLP tape speed is selected and the tape length is not sufficient to record the program to the end, the program cannot be recorded to the end. · The picture will be distorted when playing the part where the recording tape speed is switched from SP to SLP with the Auto Speed Select feature. SAP 26 Confirming the timer programs Press PROG. The screen for confirming will appear. If a power failure occurs during the timer program recording (including VCR Plus+ C 3 ® system recording (page 30) · When a power failure has occurred, the programmed contents are not effected, reset the clock P M P M Overlaps of the programs If two timer programs overlap, the recording start time of program 1 has priority over the recording off time of program 2. Program 1 (Start time) Press PROG. again to exit from confirmation page. Changing/cancelling the timer programs. 1) If the TIMER indicator is lit, press both TIMER to turn it off, and then turn the VCR on by pressing VCR POWER. To cancel a program, select the program you want to cancel in step 4, and press CANCEL. [. . . ] (5) Labor service charges for set installation. Set up, adjustment of customer controls and installation of repair or antenna systems are not covered by this warranty. Reception problems caused by inadequate antenna systems are your responsibility. (6) Warranties extend only to defects in materials or workmanship as limited above and do not extend to any product or parts which have been lost or discarded by you or to damage to products or parts caused by misuse, accident, damage caused by Acts of God, such as lightning or fluctuations in electric power, improper installation, improper maintenance or use in violation of instructions furnished by us; or to units which have been altered or modified without authorization of TACP/ THI or to damage to products or parts there of which have had the serial number removed, altered, defaced or rendered illegible. [. . . ]