User manual TOYOTA ECO26A

[. . . ] 3 How to change the power plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Part names. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Part names and their functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Quick adviser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Position the spool of thread and the spool cap on to the spool pin. Spool cap Spool of thread 2 Sewing preparations Spool pin Spool pin ( Handwheel ( ) ) Main power switch ( 1 ) 1 the thread from Pull the thread spool, and hold it with one hand. 2 Pass the thread around the thread guide with the other hand, as shown. Thread guide 6 3 the thread Pull down along the groove, and then pull it back up. 4 Pass the thread through the takeup lever from the right. 5 the thread Pull down along the groove. Check that the take-up lever is correctly threaded. Pass the thread in The thread the order shown. should be taut (3 through 5) and secure. Take-up lever 19 Using the needle threader Caution Before using the needle threader, use the main power switch to turn off the sewing machine. 11/75 to 16/100 with the needle threader. (Needle No 14/90 is included when the sewing machine is purchased. ) The needle cannot be threaded if the thread is too thick for the needle. For details on possible needle and thread combinations, refer to “Relationship between the needle, thread and fabric, and adjusting the thread tension” on page 29. zz Preparing to use the needle threader 1 Turn the handwheel towards yourself until the needle is in its highest position. ** If the needle is not in its highest position, the needle cannot be threaded. 2 Turn the pattern selection dial to “6” (straight stitch). Note: Never turn in the wrong direction. Handwheel Presser foot lever Press the presser foot holder lever in the direction of the arrow to release the presser foot. Presser foot holder lever Presser foot 26 zz Installation 1 Position the presser foot pin directly below the groove in the presser foot holder. Presser foot holder 2 Groove Sewing preparations Presser foot pin 2 Lower the presser foot lever to secure the presser foot. Presser foot lever Tip In order to avoid losing the presser foot, we recommend storing the machine when it is not being used with the needle and the presser foot lowered. 27 Changing the needle Caution Before changing the needle, use the main power switch to turn off the sewing machine. Be sure to dispose of them in a safe place away from children. Not doing so could cause an injury. 1 2 Turn the handwheel towards yourself to raise the point of the needle higher than the needle plate. Hold the needle in one hand, loosen the needle clamp screw with the screw driver for the needle plate, and remove the needle. Note: Do not remove the needle clamp screw. Loosen the needle clamp screw to remove the needle. Face the flat surface of the needle to the rear and insert until it makes contact with the pin. Firmly tighten the needle clamp screw with the screw driver for the needle plate. Pin Screw driver for the needle plate Needle clamp screw Flat surface zz Correct needle selection Good needle If a faulty needle is used, not only could it impair the sewing performance, but it could also damage the needle plate or hook, or break the needle. ** Incorrect stitching or thread breaking, try replacing the needle. ÍFaulty needle The entire needle is bent 28 The point of the needle is crushed / worn away The point of the needle is bent Relationship between the needle, thread and fabric, and adjusting the thread tension The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric. [. . . ] ** If the bobbin case is not installed correctly, the handwheel does not turn smoothly. If this occurs, remove the needle plate and bobbin case, and attach them again. 4 Maintenance 47 Changing light bulb Warning Before changing the light bulb, use the main power switch to turn off the sewing machine, remove the power plug from the outlet, and then wait until the bulb cools. Not doing so could cause a burn or electric shock. 8 1 Loosen the screw with a + screw driver of your own, and take off the face cover in the direction of the arrow. Screw Face cover 8 2 Turn the light bulb counterclockwise as the arrow in the diagram and remove. Turn the new light bulb clockwise to install. Note: Use a light bulb with a maximum power of 15 W. [. . . ]