User manual TOYOTA SP10

[. . . ] SP10 Series HOME-USE SEWING MACHINE INSTRUCTION MANUAL · Read this manual carefully before use and always follow the instructions. · Keep the manual in a convenient place for easy reference. · If you give the sewing machine to someone else, also give them this instruction manual. Contents Before use · · · · · · · · Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 How to change the power plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Support the thread on the sewing machine with one hand, using the other hand pass the thread around the thread guide as shown in the diagram. 14 4 5 Pass the thread end through the hole of the bobbin as shown. Hole Place the bobbin on to the thread winding spindle so the groove will meet the shaft projection. Thread Groove Thread winding spindle Shaft projection 6 7 Hold the thread end and push the thread winding switch to the left and start winding. Pass the thread through the take-up lever. Take-up-lever 8 Pass the thread through the right side needle guide. Check that the thread is threaded correctly. Raise the presser foot and pull the upper thread towards yourself. Lower the presser foot and pull the upper thread towards yourself. It should be resistant and difficult to pull. Needle guide 9 Pass the thread through the needle eye from the front. Front 15cm 18 Sewing preparations · Pulling up the lower thread 1 Hold the end of the thread, turn the handwheel towards yourself for one full turn, and stop when the needle is at its highest position. Handwheel Note: Always turn the handwheel towards yourself (in the direction of the arrow). If you turn it in the wrong direction it could tangle the thread. Note: If the thread is tight the lower thread will not come out, so hold the thread loosely. 2 Pull up the upper thread and the loop of the lower thread will come out. Pull out this lower thread. Upper thread Lower thread 3 Align the upper thread and lower thread, and thread through the groove of the presser foot. Pull back about 15 cm. 15cm 19 Sewing preparations · Application of each stitch pattern Caution Don't turn the pattern selection dial while operating the sewing machine. Turn the handwheel towards yourself to raise the needle in the highest position. Turn the pattern selection dial to choose the pattern. Pattern selection dial Buttonhole Blind hem stitch Zigzag Applique Overcasting Scallop stitch Straight stitch Sewing-seams Zipper insertion Castle stitch Thin fabric straight stitch Decorative stitch Fagotting Mending stitch Thin fabric overcasting Decorative stitch Serpentine 20 Sewing preparations · Changing the presser foot Caution Remove the power plug from the outlet when changing the presser foot. Not doing so could cause an injury. Removal 1 Raise the presser foot lever. 2 Turn the handwheel towards yourself to raise the needle. Note: Never turn in the wrong direction. Handwheel Presser foot lever 3 Press the presser foot holder lever in the direction of the arrow to release the presser foot. Presser foot holder lever Presser foot 21 Installation 1 Position the presser foot pin directly below the groove in the presser foot holder. Presser foot holder Groove Presser foot pin 2 Lower the presser foot lever to secure the presser foot. Presser foot lever 22 Sewing preparations · Changing the needle Caution Remove the power plug from the outlet when changing the needle. Be sure to dispose of them in a safe place away from children. Not doing so could cause an injury. 1 2 Turn the handwheel towards yourself to raise the end of the needle higher than the needle plate. Hold the needle in one hand, loosen the needle clamp screw with the screw driver for the needle plate, and remove the needle. Note: Do not remove the needle clamp screw. [. . . ] No grounding means are provided on a double-insulated product nor should a means for grounding be added to the product. Servicing a double-insulated product requires extreme care and should only be done by qualified service personnel with knowledge of the system under his or her responsibility. Replacement parts for a doubleinsulated product must be identical to those parts in the product. The symbol is marked on the double-insulated product. Others · Safety precaution about the battery Warning If the alkaline solution from the battery should get in the eyes or come into contact with the skin or clothes, rinse with a large quantity of clean water and consult a doctor immediately. [. . . ]