User manual TP-LINK TD-W8920GB

[. . . ] TD-W8920G 108M Wireless ADSL2+ Router User Guide TD-W8920G 108M Wireless ADSL2+ Router Rev: 1. 0. 2 1910010014 TD-W8920G 108M Wireless ADSL2+ Router User Guide COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO. , LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. [. . . ] Note: When you add an Outgoing IP Filtering entry, you must configure at least one condition on the screen above except the Filter name. If you leave the Protocol blank, it means that the rule is effective to all protocols, if you leave the Source IP Address and/or Destination IP Address blank, it suggests that all Source IP Addresses and/or Destination IP Addresses are controlled by the rule, if you leave the Source Port and/or Destination Port blank, it suggests that all Source Ports and/or Destination Ports are controlled by the rule. IP Filtering - Incoming Choose "Advanced Setup" "Security" "IP Filtering" "Incoming", you can configure Incoming Filtering rules on the screen (shown in Figure 4-26). The Incoming IP Filtering feature allows some IP traffic from WAN to access some local addresses. By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled. However, some IP traffic can be ACCEPTED by setting up filters. 6. 37 TD-W8920G 108M Wireless ADSL2+ Router User Guide Figure 4-26 Setup an Incoming IP Filtering rule: 1. Click the Add button (pop-up Figure 4-26), and then you will set the new rule in the next screen (shown in Figure 4-27). Figure 4-27 2. Enter the Filter name for the rule, it is exclusive and must be filled in. Select Protocol in the drop-down list, enter Source IP address, Source Subnet Mask, Source Port, Destination IP address, Destination Subnet Mask, and Destination Port for the rule. Select at least one WAN interfaces displayed below to apply this rule. Click the Save/Apply button to save this entry. 4. 5. 38 TD-W8920G Note: 108M Wireless ADSL2+ Router User Guide When you add a Incoming IP Filtering entry, you must configure at least one condition on the screen above except the Filter name. If you leave Protocol blank, it means that the rule is effective to all protocols, if you leave the Source IP address and/or Destination IP address blank, it suggests that all Source IP addresses and/or Destination IP addresses are controlled by the rule, if you leave the Source Port and/or Destination Port blank, it suggests that all Source Ports and/or Destination Ports are controlled by the rule. MAC Filtering Choose "Advanced Setup" "Security" "MAC Filtering", you can configure MAC Filtering rules on the screen (shown in Figure 4-28). The section allows you to control access to the Internet by users on your local network based on their MAC Address. Figure 4-28 Change Policy: There are two policies for the MAC filters: FORWARDED and BLOCKED. Click the button to change from one policy to another. When you select FORWARDED, it means that all MAC layer frames will be forwarded except those matching with any of the specified rules in the table (shown in Figure 4-28). While BLOCKED means that all MAC layer frames will be blocked except those matching with any of the specified rules in the table above. Add: Click the Add button, and then you can add a new MAC Filter in the next screen (shown in Figure 4-28). Remove: Select the check box in the table (shown in Figure 4-28) and then click the Remove button, and then the corresponding entry will be deleted in the table. 39 TD-W8920G To setup a MAC Filtering rule: 1. 108M Wireless ADSL2+ Router User Guide Click the Add button (pop-up Figure 4-28), then you will set the new rule in the next screen (shown in Figure 4-29). Figure 4-29 2. Select Protocol Type in the drop-down list for the rule. Enter Destination MAC Address and Source MAC Address in the text box. [. . . ] The transport independence of RPC isolates the application from the physical and logical elements of the data communications mechanism and allows the application to use a variety of transports. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in 76 TD-W8920G small offices. 108M Wireless ADSL2+ Router User Guide SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. [. . . ]