User manual TP-LINK TL-SG1016D

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. [. . . ] Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Package Contents The following items should be found in your box: One TL-SG1016D/TL-SF1008D/TL-SF1016D Switch One Power Adapter This User Guide Note: Make sure that the box contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. CONTENTS Chapter 1. Note: The three devices of TL-SG1016D, TL-SF1008D and TL-SF1016D are sharing this User Guide. For simplicity, we will take TL-SF1016D for example throughout this Guide, The differences between them are: TL-SG1016D Switch with 5 10/100Mbps Auto-Negotiation RJ45 ports. TL-SF1008D Switch with 8 10/100Mbps Auto-Negotiation RJ45 ports. TL-SF1016D Switch with 16 10/100Mbps Auto-Negotiation RJ45 ports. 1. 3 Features Complies with IEEE 802. 3, IEEE 802. 3u standards 5/8/16 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto-MDI/MDIX Supports IEEE802. 3x flow control for Full Duplex mode and backpressure for Half Duplex mode Supports MAC address auto-learning and auto-aging LED indicators for monitoring power, link, activity 1 Plastic case, desktop or wall-mounting design External Power Adapter supply Chapter 2. Installation 2. 1 Mounting the Switch on a Desk To install the Switch, please follow the steps: 1) 2) You can place the Switch on a flat desk. Please inspect the Power Adapter carefully and make sure that it is properly connected to a power source. 3) Ensure adequate ventilation space around the switch for dissipating heat and air. Note: Please avoid any heavy thing placed on the switch. 2. 2 Power On Powering on the Switch, it will automatically initialize and its LED indicators will respond as follows: 1) All of the Link/Act LED indicators will flash momentarily, which represents a resetting of the system. 2) The Power LED indicator will light all the time. Note: If the LED indicators don't respond as described above, please check the power supply and its connection. 2 Chapter 3. Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. 3. 1 Front Panel Figure 3-1 TL-SF1016D Switch Front Panel The Switch's LEDs are located on the front panel. [. . . ] 2) The Power LED indicator will light all the time. Note: If the LED indicators don't respond as described above, please check the power supply and its connection. 2 Chapter 3. Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. 3. 1 Front Panel Figure 3-1 TL-SF1016D Switch Front Panel The Switch's LEDs are located on the front panel. Power LED: LEDs (1-16): This indicator will light up when the Switch powers on. [. . . ]