User manual TP-LINK TL-SG1024D

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. [. . . ] Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. CONTENT Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1. Introduction of the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 1. 2 1. 3 2. 1 2. 2 3. 1 3. 2 Overview of the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Mounting the Switch on a Desk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 3. The power of all the connected PoE ports is >=43w. No power may be supplied if additional PDs are connected. The power of all the connected PoE ports is <43w, or there is No PD connected to the corresponding port. Data transmitting or receiving on corresponding port. There is a 10Mbps or 100Mbps device connected to the corresponding port. No device connected to the corresponding port. PoE ports (port-1~port-4) On(red) Off Flashing (red) On(red) PoE MAX Off Flashing (green) Link/Act (port-1~port-8) On(green) Off 5 On(green) 100Mbps (port-1~port-8) Off There is a 100Mbps device connected to the corresponding port. There is a 10Mbps device connected to the corresponding port, or there is no device connected to the corresponding port. Note If all PoE PDs power consumption is >= 53w, a priority* will be arranged among the PoE ports like port-1 > port-2 > port-3 > port-4, then the system will cut off the power of the lowest-priority port. *Priority: This function will help protect the system when the system power is overloaded. For example, Port 1, 2 and 4 is using 15. 4w (maximum power for per port is 15. 4W), the system power is 46. 2w in total. If there is an additional PD inserted to Port 3 with 10w, then the system will cut off the power of Port 4 because of the overloaded power, this means Port 1, 2 will use 15. 4w, and Port3 will use 10w , no power will be supplied to Port 4. 3. 2 Rear Panel Figure 3-2 TL-SG1024D Switch Rear Panel 6 The following parts are located on the rear panel: Power (48V): 48V indicates the input voltage of the power adapter provided with this TL-SG1024D Switch. The Power socket is where you will connect the power adapter. [. . . ] The Power socket is where you will connect the power adapter. PoE Ports (1-4): These ports support PoE function which integrates power and data onto one the same cable. Once the device you connect to the switch is identified, the switch will supply power through the PoE port, and then you can use it as a 10/100Mbps Auto-Negotiation RJ45 Ethernet port. The working status can be indicated by the corresponding LEDs on the front panel. [. . . ]