User manual TP-LINK TL-SG2216WEB

[. . . ] User's Guide TL-SG2216WEB 16-port Gigabit Web Smart Switch TL-SG2224WEB 24-port Gigabit Web Smart Switch COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK Technologies Co. , Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co. , Ltd. [. . . ] TFTP Server IP: Indicates the IP address of TFTP server. Further explanation File transfer types: System Upgrading: Means downloading the executable file from TFTP server to switch and upgrading the system. 31 TL-SG2216WEB/TL-SG2224WEB Web Smart Gigabit Switch Family User's Guide Configuration Backup: Means backing up the current configuration of the switch to TFTP server. Configuration Loading: Means downloading the configuration from TFTP server to the switch and update it. Notice: 1) Please make sure the target file exits on TFTP server before downloading. 2) Please make sure the TFTP server is in operation. 3) Breaks should be avoided in file transfer; otherwise, the switch may be damaged. 5. 3. 1. 3 Reboot & Reset This page is shown below. Figure 5-15 Reboot & Reset A prompt will display if a button is pressed. For example, if the button "Softreset" is pressed, a message box will be activated as showed in figure 5-16. Figure 5-16 Message Box 32 TL-SG2216WEB/TL-SG2224WEB 5. 3. 1. 4 User Web Smart Gigabit Switch Family User's Guide This page provides the interface of configuring username and password. Figure 5-17 User Configuration You are kindly suggested to retype the new password in "Confirm new password" box instead of copying in order to avoid mistakes. Notice: 1) Only letters, numbers and punctuations can be inputted into username and password field, other characters are considered illegal. The length of username and password ranges from 1 to 16 characters. 2) The initial username and password is supervisor/supervisor. 5. 3. 2 Port Setting 5. 3. 2. 1 Port Parameter This page contains the following fields: 33 TL-SG2216WEB/TL-SG2224WEB Web Smart Gigabit Switch Family User's Guide Figure 5-18 Port Parameter Port Status: Indicates whether the port is operational or non-operational. " Enable" Indicates that the port is operational and "Disable" Indicates the port is non-operational. If a port is unused for a long time, it can be set to be non-operational to cut down the energy cost. Notice: 1) You can't manage the switch via the port, which is non-operational, please set the value of the management port to "enable". 2) SFP port is a combo port sharing a connection with a Giga port. In TLSG2216WEB, SFP1 and port 15 compose a combo port, SFP2 and port 16 compose a combo port; In TL-SG2224WEB, SFP1 and port 23 compose a combo port, SFP2 and port 24 compose a combo port. For a 34 TL-SG2216WEB/TL-SG2224WEB Web Smart Gigabit Switch Family User's Guide combo port, only one operation type can be active at a time, if both ports are connected at the same time, the SFP port has the priority of being active. The combo port uses the same configuration, for example, in TLSG2216WEB, if port 15 is active and the Port Status parameter is set to "Disable", when the SFP1 is active, its Port Status parameter will also be "Disable". Port Security: "Enable" Indicates the port will not learn new MAC address and only transmit the frames from the MAC address it has learned. " Disable" Indicates it will learn new MAC address. Notice: If you haven't set the static MAC address, you can't set all of the port security to be enabled, which will cause to not able to manage the switch. Flow Control: Indicates whether the flow control is enabled or disabled. Notice: If the port is working at half duplex, the settings of flow control are divided into several groups (each group includes 6 ports), for example, port 1 to 6 are assigned to group 1. The ports of the same group share the same flow control settings, so when you modify the setting of one port, those of the other ports are changed correspondingly. Duplex Mode: Possible field values are Auto, 10M HD, 10M FD, 100M HD, 100M FD and 1000M FD, "HD" stands for half-duplex and "FD" stands for full-duplex. "Auto" means auto negotiation. 35 TL-SG2216WEB/TL-SG2224WEB Web Smart Gigabit Switch Family User's Guide Notice: Though the SFP module support hot-plugging, but the configuration of Duplex Mode could not change automatically, after switching between UTP, 100M SFP and 1000M SFP on the combo port, please modify its Duplex Mode manually or re-electrify the switch to make sure the configuration is correct. The 100M SFP should be set to "100M FD" and the 1000M SFP should be set to "AUTO" or "1000M FD". Further explanation: 1) By operating on fields in the All Ports line expediently, you can set the values of all ports in the corresponding field. Some other setting pages offer the same function. 2) Parameters of Trunk member ports are configured with default values (see the Appendix B table) and cannot be configured here (see port 5 and 6 in the figure for example). 5. 3. 2. 2 Port Statistic This page displays the port statistic, it contains the following entries: Figure 5-19 Port Statistic 36 TL-SG2216WEB/TL-SG2224WEB Web Smart Gigabit Switch Family User's Guide Tx Collisions: The number of collision events seen by the MAC. [. . . ] As shown below: Figure 5-41 Port-Based priority Port: Indicates the switch port number. Priority Class: In port-based priority mode, the switch ports are classified into four priority classes: lowest, lower, higher and highest. All the packets 58 TL-SG2216WEB/TL-SG2224WEB Web Smart Gigabit Switch Family User's Guide entering from the port of the switch are forwarded in the corresponding priority queue. Further Explanation When priority rule is configured as "weighted", a 1, 2, 4, 8 weighting is applied to forward these four classes of packets. 5. 3. 6. 3 Port Default Priority This page is revealed when the "IEEE802. 1p" mode is configured. [. . . ]