User manual TP-LINK TL-SG3424P

[. . . ] Copyright © 2005 TP-LINK Technologies Co. , Ltd. All rights reserved. COPYRIGHT & TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1: About this User's Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The name of the new group can't be the same as the names that already existed in the application. After adding the group, you can rename the group and delete it at any time. a) Click main menu->System->Add Group. As figure 5-3. -9- TL-SG3424P/TL-SL2226P+ Remote Smart Switch User Guide Figure 5-3 Click Add Group, you can see the dialog. As figure 5-4 Figure 5-4 b) Click the right button at Please Add Group on initialized interface and then pop up a menu, click Add Group. As figure 5-5 - 10 - TL-SG3424P/TL-SL2226P+ Remote Smart Switch User Guide Figure 5-5 c) Click the add group icon on the tool bar. As figure 5-6. Figure 5-6 2) Add device and node in device group. In device group, you can add device and node, which are just like file and folder. The hiberarchy of node and device of a group are not more than five. If there is the fifth hiberarchy, the fifth hiberachy can only be a device. The device and node can be changed at any time you want. As figure 5-16. Figure 5-16 Now you can configure each parameter of the port except port priority. 1) Mode: 10Base-T/100Base-TX Ports Auto (default): other end. auto-test the speed and negotiate the duplex mode with the - 17 - TL-SG3424P/TL-SL2226P+ 10HD: 10Mbps, Half-Duplex. 100FD: 100Mbps, Full-Duplex 2) Flow Control: Remote Smart Switch User Guide Disable: The port won't produce Flow Control packets and will discard the Flow Control packets received. Enable: The Switch will negotiate Flow Control on the specified port according to Full-Duplex or Half-Duplex. 3) Port Security: When you configure the Port Security of a port to be Enable, the port won't learn any new MAC address. Furthermore, the port only transfers the data accordant to static MAC Address. If the port does not bind any static MAC address, the port will not transfer data. When the Port Security of a port is disabled, the port will automatically learn any new MAC Address and transfer data. Default setting: Disable 4) Default PVID: There is the choice only in the IEEE802. 1Q Tag VLAN mode. Every port on the Switch has a default VID which is the VID for an untag Tag received by the port. [. . . ] Caution: If you configure the Static MAC Table, it will take effect immediately, you needn't save it. Broadcast Storm Broadcast Storm interface is as follows. When Broadcast State is Disable, other parameters can't be changed. - 30 - TL-SG3424P/TL-SL2226P+ Remote Smart Switch User Guide Figure 6-16 2) Network Config Network Config interface is as follows, you can change the switch's IP, gateway, you can not change the switch's MAC address. Figure 6-17 Press w or s key to move cursor, press space to edit the switch's IP address, Default gateway. Input the new IP address and gateway, press enter. [. . . ]