User manual TP-LINK TL-SL2109 INSTALLATION GUIDE

[. . . ] COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK Technologies Co. , Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co. , Ltd. [. . . ] You also can use the TRUNK between the switchs to solve the traffic. TL-SL2109's TRUNK function supports one TRUNK, which is made up of the seventh and the eighth port, the TRUNK port's bandwidth can get to 400Mbps. 2. 2 Virtual Local Area Network The Virtual Local Area Network can be out of the constraints of the physical connections. You can move the workstations among the workgroup and the subnet without changing the physical connection. The work stations build up the logical workgroup or the virtual subnet to improve the performance of the system. Poise the flux in the network and utilize the source of the device reasonedly. In the same time, the VLAN decompresses the management and maintenance of the network. Virtual Group: The members of the groups' communication with each other will be greatly improved. And not required the router in the system. Safety: Because only the legal user can forward the information, the safety of the network will be improved. Economize cost: You can use VLAN in the network without adding the router or re-distributing the cable. Port-based VLAN is the usual technology of the TL-SL2109. The TL-SL2109P supplies nine Port-based VLAN. 2. 3 Priority The TL-SL2109 supplies the port-based priority. The Switch had two levels, low and high. The switch forwards the frames based on the level of the priority. The frames with high level priority can be solved firstly. -3- TL-SL2109 8+1G Gigabit Ethernet Smart Switch User Guide 2. 4 Main features Complies with IEEE 802. 3IEEE 802. 3ab 8 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto-MDI/MDIX 1 10/100/1000Mbps Auto-Negotiation RJ45 ports supporting Auto-MDI/MDIX Supports IEEE802. 3x flow control for Full Duplex mode and backpressure for half-duplex mode Supports port-based VLAN with 9 entries Supports TRUNK Supports Port Enable/Disable Supports Static Port Priority with 2-level priority queuing 1 console port supporting configured software setting Desktop or rack-mountable steel case Internal power supply -4- TL-SL2109 8+1G Gigabit Ethernet Smart Switch User Guide Chapter 3: Installation 3. 1 Installation Firstly, please place the switch following the steps: The surface must support at least 5kg; The power source must be within 1. 5m; Check the power cable carefully to make sure the connection to AC power; Leave enough space for the ventilation. 3. 1. 1 Installation on the desktop 1. Place the Switch on a desk which has enough space; Take off the four pads' adhesive tape and adhere to the four circle grooves on the bottom of the switch respectively; Turn off the switch again, place on the desktop. 3. 1. 2 Rack Installation The TL-SL2109 can be mounting in an EIA Standard size 19 inches rack. Attach the mounting brackets to each side of the TL-SL2109 with the screwes; 2. Use the screwes to secure the switch to the rack. . Figure 3-1 Rivet the "L" brackets onto the Switch -5- TL-SL2109 8+1G Gigabit Ethernet Smart Switch User Guide Figure 3-2 Fasten the Switch in the rack 3. 1. 3 Hang on the wall The TL-SL2109 can be hung on the wall. Drill two holes with a 6mm diameter on the wall, the distance between the holes is 160mm. Press the plastic tube in the hole entirely, then put screws in the plastic tubes, screw them with a few body stuck out the wall; 3. Place the switch to the two screws by the holes in the switch. 3. 1. 4 Power on The TL-SL2109 can be used with the power source in the range of 110 to 260 VAC, 50-60Hz. After the power is on, the power LED will be light. [. . . ] The switch can only use the port-based priority. Default Setting: Port Number (Low) - 15 - TL-SL2109 8+1G Gigabit Ethernet Smart Switch User Guide 4. 4 PortClose Setting The PortClose Setting can close the port(s). It (They) can not transfer or receive the packages. The port (1-8) and the gigabit port configure in the different place in the software. [. . . ]