User manual TP-LINK TL-SL2226

[. . . ] 2 1. 2 Port TRUNK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 3 AUTO MDI/MDIX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 4 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2: Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Low cost: You can move the workstations freely in the VLAN, and there need no routers and replacing the cable. 1. 2 Port TRUNK Generally, TRUNK means that two switches can be connected two or more than two (but less than five) ports side-by-side to supply more band width and more throughput and self-resume technic. This is to say, TRUNK is to treat several physical connections as one logic connection. TRUNK is very useful to several lower speed device to a high speed device. The current device can simply add more NIC connecting to the server to resolve the traffic between the switches and the servers. 1. 3 AUTO MDI/MDIX The switch supports MDI/MDIX function, every port of the Switch can be used as normal port and uplink port. It becomes easy to use, plug and play, when connecting to the other switches and hubs, whether the direct cable and the crossover cable or not. The switch, a smart auto-negotiated Ethernet switch, supplies the method of promotion of the workstation resource. 1. 4 Features Complies with IEEE802. 3, IEEE802. 3u, IEEE802. 3ab and IEEE802. 3z (only for TL-SL2226P) standards 8/16/24 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto MDI/MDIX -2- TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide 1/1/2 extension slots supporting 100M fiber module card (TL-SM201 series) and TL-SL2226P supports 1000M fiber/UTP module (TL-SM301 series) Supports IEEE802. 3x flow control for Full Duplex mode and backpressure for half-duplex mode Supports Port Enable/Disable Supports 9 Port VLAN and 9 IEEE802. 1Q Tag VLAN (for TL-SF2109P), 17 Port VLAN ( for TL-SF2117P) and 26 Port VLAN ( for TL-SL2226P) Supports Port Mirror (only for TL-SF2117P) Supports Port Trunk, up to 1 Trunk group (for TL-SF2109P) and 8 Trunk group (for TL-SL2226P) Supports Static Priority, TOS and 802. 1p Class of Service with 2-level priority queues (for TL-SF2109P and TL-SF2117P) Easy read LED indicators for installation and operation Support a RS232 interface for smart configuration (example :VLAN, Trunk, Priority ) Desktop Steel case (for TL-SF2109P) and standard 19-inch rack-mountable steel case (for TL-SF2117P and TL-SL2226P), internal power supply -3- TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide Chapter 2: Installation 2. 1 Mounting the Switch on a Desk Before place the Switch on a desk, attach four rubber footpads to the flutes on the Switch bottom, then lay the Switch on the desktop, where can be have as much as 5kg placed on top. Note: Make sure there is a grounded AC outlet within 1. 5 meters, and working well. Make sure there is free space for radiating heat and air. Make sure not to place anything to heavy on top of the switch. 2. 2 Mounting the Switch in a Rack The dimension of the Switch is designed according to the standard 19" rack-mountable steel case of Electronic Industries Association. Turn off all the equipment connected to the Switch before mounting it in the rack, then rivet the two "L" brackets onto each side of the Switch, fasten it with screwes in the rack. Figure 2-1 Rivet the "L" brackets onto the Switch -4- TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide Figure 2-2 Fasten the Switch in the rack 2. 3 Power on The Switch is powered by AC power supply. Powering on the Switch, it will automatically initialize and its LED indicators should respond as follows: 1) All of the LED indicators will flash momentarily for one second, which represent a resetting of the system. 2) The power LED indicator will remain ON. -5- TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide Chapter 3: Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. Cautions: All the pictures are based on the TL-SF2109P in the manual. The others are similar with the TL-SF2109P. 3. 1 Front Panel The front panel of the TL- SF2109P consists of switch LED indicators, 8 10/100Mbps RJ-45 ports, and 1 serial port Connect the female of the power cord head here. Console 10/100Mbps Fast Ethernet Smart Switch Figure 3-1 TL- SF2109P Switch Front Panel sketch Serial port: Config the system by the serial cable (more details in chapter 4) 3. 2 Rear Panel The rear panel of the TL-SF2109P only features a power receptacle, which is an AC power receptacle , and 1 extension slots. Connect the female of the power cord head here, and the male head to the AC power outlet. Extension slot: This is a optional module slot which can connect to a 100M UTP/fiber (Tl-Sf2109P and TL-SF2117P) or a 1000M fiber module or 10/100/1000M UTP module card(TL-Sl2226P). Slot Figure 3-2 TL- SF2109P Switch Rear Panel sketch Power connector: This is a 3-Phase power socket, Plug the connector with a 100~240VAC/50-60Hz power supply. -6- TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide 3. 3 LED indicators The LED indicators include Power, 100Mbps, Link/ACT and slot can display the working status of the switch, more details as follows: 10/100Mbps Fast Ethernet Smart Switch Figure 3-3 TL- SF2109P Switch LEDs sketch Power LED: After power on, the LED will be light always. If it is turned off, check the connection of the power source. 100Mbps LED: When a port is connected to a device with the 100Mbps, the corresponding green LED is light, or else it is turned off. Link/ACT: when transferring the data between two devices, the corresponding LEDs will be flicker with green. Slot: When inserted a UTP/fiber module card, LED is green. If it is turned off, check the connection of the card. (The LED is only in TL-SF2109P) 3. 4 Optional Slot Module TL-SL2226P supports the TL-SM201/TL-SM301 serials module cards. [. . . ] "1 : n" means low priority and high priority, "0 : 1" - 20 - TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide means that high priority is first always. 4. 7 MAC Address Age Time The MAC Address will auto age out after 5 minutes if it is not updated in MAC address table, this time is aging time. Click the "MAC Address Aging" in settings menu or the "MAC Address Aging Setting" icon. - 21 - TL-SF2109P/TL-SF2117P/TL-SL2226P 2. You can select as follows. Ethernet Smart Switch User Guide 4. 8 Config effect 1. Write to Switch After finishing setting above, click "write to Switch", the switch will restart and reserve the results having been configed. 2. Restore factory setting Click the "Recover Factory Configuration" in menu, and it will restore the parameters to default value and restart the switch. - 22 - TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide 4. 9 "Save", "Open" Configuration file 1. [. . . ]