User manual TP-LINK TL-WN725N

[. . . ] http://www. tp-link. com is a registered trademark of TP-LINK TECHNOLOGIES CO. , LTD. Other brands and product names are trademarks or FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] 2346 is the default setting and is recommended. DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. Enable WMM - WMM function can guarantee the packets with high- priority messages being transmitted preferentially. Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time. Note: If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values, otherwise may result in lower wireless network performance. 4. 6. 5 Wireless Statistics Choose menu "WirelessWireless Statistics", you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-17 The router attached wireless stations MAC Address - The connected wireless station's MAC address Current Status - The connected wireless station's running status, one of STA-ASSOC / WPA / WPA-PSK / WPA2 / WPA2-PSK Received Packets - Packets received by the station Sent Packets - Packets sent by the station - 34 - TL-WN725N/TL-WN725ND Wireless N Router You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. If you want to delete the entry, click the - 37 - TL-WN725N/TL-WN725ND Delete. Click the Save button. Wireless N Router Click the Enable/ Disabled All button to make all entries enabled/disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and Click the Previous button to return the previous page. 4. 8 Forwarding Figure 4-23 The Forwarding menu There are four submenus under the Forwarding menu (shown in Figure 4-23): Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 4. 8. 1 Virtual Servers Choose menu "ForwardingVirtual Servers", you can view and add virtual servers in the next screen (shown in Figure 4-24). Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP. A virtual server is defined as a service port, and all requests from the Internet to this service port will be redirected to the computer specified by the server IP. Any PC that was used for a virtual server must have a static or reserved IP Address because its IP Address may change when using the DHCP function. Figure 4-24 Virtual Servers Service Port - The numbers of External Ports. You can type a service port or a range of service ports (in XXX ­ YYY format, XXX is the start port number, YYY is the end port number). - 38 - TL-WN725N/TL-WN725ND Wireless N Router IP Address - The IP Address of the PC providing the service application. Protocol - The protocol used for this application, either TCP, UDP, or All (all protocols supported by the router). Status - The status of this entry either Enabled or Disabled. (pop-up Figure 4-25) Select the service you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the number of the service port or service port range in the Service Port box. [. . . ] 3) Right click the icon that showed below, select Properties on the prompt page. Figure B-1 4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP). - 66 - TL-WN725N/TL-WN725ND Wireless N Router Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below: Setting IP address automatically Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the Figure below: - 67 - TL-WN725N/TL-WN725ND Wireless N Router Figure B-3 Setting IP address manually 1 2 Select Use the following IP address radio button. And the following items available If the router's LAN IP address is 192. 168. 1. 1, type IP address is 192. 168. 1. x (x is from 2 to 254), and Subnet mask is 255. 255. 255. 0. 3 Type the router's LAN IP address (the default IP is 192. 168. 1. 1) into the Default gateway field. [. . . ]