User manual TP-LINK TL-WR1043N INSTALLATION GUIDE

[. . . ] TL-WR1043N TL-WR1043ND Wireless N Gigabit Router Rev: 1. 0. 0 1910010216 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. Copyright © 2009 TP-LINK TECHNOLOGIES CO. , LTD. [. . . ] Free - The available space of the USB driver. Use% - The percentage of the used space. Permissions - Read-Only or Read/Write access to the volume designated as the share. Shared - Indicates the shared or non-shared status of the volume. Click the Start button to start the Network Sharing service. Click the Stop button to stop the Network Sharing service. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. A message will appear on your web browser when it is safe to detach the USB disk. Click the Rescan button to start a new scan. Follow the instructions below to set up your Router as a file server: 1. Plug an external USB hard disk drive or USB flash drive into this Router. Click the Rescan button to find the USB drive that has been attached to the Router. To specify a volume that the Network Sharing users can access, click the Edit link in the Properties column and configure the share settings in figure 4-31. Set the Network Sharing user's username and password on User Accounts page. Click the Start button to start the Network Sharing service. Now the Network Sharing users inside your local network can access files on the USB drive from Internet Explorer at its Share Name followed by the Router's LAN IP address, for example: \\192. 168. 1. 1\MyShare. Figure 4-31 Sharing Settings - 51 - TL-WR1043N/TL-WR1043ND Note: 1. 5. Wireless N Gigabit Router The Router cannot automatically locate new USB drive. You have to click the Rescan button manually to display a list of volumes and information about them. The new settings will not take effect until you restart the service. To unplug the USB drive, click Eject Disk button first. Simply pulling USB drive out of the USB port can cause damage to the device and loss of data. Mounted volumes are subject to the 8-volume limit. [. . . ] In the Preferred DNS Server field you can enter the same value as the Default gateway or type the local DNS server IP address. - 103 - TL-WR1043N/TL-WR1043ND Wireless N Gigabit Router Now: Click OK to keep your settings. - 104 - TL-WR1043N/TL-WR1043ND Wireless N Gigabit Router Appendix C: Specifications General Standards Protocols Ports IEEE 802. 3, 802. 3u, 802. 11b, 802. 11g and 802. 11n (draft 2. 0) TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP One 10/100/1000M Auto-Negotiation WAN RJ45 port, Four 10/100/1000M Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX, One USB port 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100 STP (maximum 100m) Cabling Type 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100 STP (maximum 100m) 1000BASE-T: UTP category5, 5e cable (maximum 100m) EIA/TIA-568 100 STP (maximum 100m) LEDs Safety & Emissions Wireless Frequency Band Radio Data Rate Channels Frequency Expansion Modulation Security 2. 4~2. 4835GHz 11nup to 300MbpsAutomatic 11g54/48/36/24/18/12/9/6MbpsAutomatic 11b11/5. 5/2/1MbpsAutomatic 13 DSSS(Direct Sequence Spread Spectrum) DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM WEP/WPA/WPA2/WPA2-PSK/WPA-PSK 270M: -68dBm@10% PER; 130M: -68dBm@10% PER 108M: -68dBm@10% PER; 54M: -68dBm@10% PER 11M: -85dBm@8% PER; 6M: -88dBm@10% PER 1M: -90dBm@8% PER 20dBm(max) 3dBi * 3 Operating : Storage: Operating: Storage: 0~40 (32~104) -40~70(-40~158) 10% - 90% RH, Non-condensing 5% - 90% RH, Non-condensing Power, System, WLAN, WAN, LAN (1-4), USB , QSS FCC, CE Sensitivity @PER RF Power Antenna Gain Environmental and Physical Temperature. Humidity - 105 - TL-WR1043N/TL-WR1043ND Wireless N Gigabit Router Appendix D: Glossary 802. 11n - 802. 11n builds upon previous 802. 11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802. 11n development process and promote a technology specification for interoperability of next-generation wireless local area networking (WLAN) products. [. . . ]