User manual TRANSCEND TS16GCF150 DATASHEET

[. . . ] TS4G~32GCF150 TS4G~32GCF150 Description The Transcend CF 150X is a High Speed Compact Flash Card with high quality Flash Memory assembled on a printed circuit board. 150X CompactFlash Card Features · CompactFlash Specification Version 4. 1 Complaint · RoHS compliant products · Single Power Supply: 3. 3V±5% or 5V±10% · Operating Temperature: -25oC to 85oC · Storage Temperature: -40oC to 85oC · Operating Humidity (Non condensation): 0% to 95% · Storage Humidity (Non condensation): 0% to 95% · Built-in 24-bit ECC (Error Correction Code) functionality and global wear-leveling algorithm ensures highly reliable of data transfer 24bit BCH ECC (4k+208 byte per page flash) · Operation Modes: PC Card Memory Mode PC Card IO Mode True IDE Mode · True IDE Mode supports: Ultra DMA Mode 0 to Ultra DMA Mode 5(UDMA5 must work under 3. 3V), MultiWord DMA Mode 0 to MultiWord DMA Mode 4 Placement Dimensions PIO Mode 0 to PIO Mode 6 · PC Card Mode supports up to Ultra DMA Mode 5 · True IDE mode: Fixed Disk (Standard) · PC Card Mode: Removable Disk (Standard) · Durability of Connector: 10, 000 times · MTBF: 1, 000, 000 hours · Support S. M. A. R. T (Self-defined) · Support Security Command · Compliant to CompactFlash, PC Card Mode, and ATA standards · Support Global Wear-Leveling, Static Data Refresh, Early Retirement, and Erase Count Monitor functions to extend product life Transcend Information Inc. 1 V1. 0 TS4G~32GCF150 TS4G~32GCF150 150X CompactFlash Card Transcend Transcend Information Inc. 2 V1. 0 TS4G~32GCF150 TS4G~32GCF150 Block Diagram 150X CompactFlash Card Transcend Information Inc. 3 V1. 0 TS4G~32GCF150 TS4G~32GCF150 Pin Assignments and Pin Type PC Card Memory Mode Pin Num 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Signal Name GND D03 D04 D05 D06 D07 -CE1 A10 -OE A09 A08 A07 VCC A06 A05 A04 A03 A02 A01 A00 D00 D01 D02 WP -CD2 -CD1 D11 D13 D14 D15 1 150X CompactFlash Card PC Card I/O Mode Pin Num 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Signal Name GND D03 D04 D05 D06 D07 -CE1 A10 -OE A09 A08 A07 VCC A06 A05 A04 A03 A02 A01 A00 D00 D01 D02 -IOIS16 -CD2 -CD1 D11 D13 D14 D15 1 1 1 1 1 1 True IDE Mode4 In, Out Type Ground Pin Num 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Signal Name GND D03 D04 D05 D06 D07 -CS0 A10 2 Pin Type In, Out Type Ground Pin Type Pin Type In, Out Type Ground I/O I/O I/O I/O I/O I I I I I I I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U I1Z I3U I1Z I1Z I1Z Power I1Z I1Z I1Z I1Z I1Z I1Z I1Z I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 OT3 Ground Ground I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U Ground I/O I/O I/O I/O I/O I I I I I I I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U I1Z I3U I1Z I1Z I1Z Power I1Z I1Z I1Z I1Z I1Z I1Z I1Z I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 OT3 Ground Ground I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U Ground I/O I/O I/O I/O I/O I I I I I I I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3Z I1Z I3U I1Z I1Z I1Z Power I1Z I1Z I1Z I1Z I1Z I1Z I1Z I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 ON3 Ground Ground I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3Z Ground -ATA SEL A09 A08 A07 A06 A05 A04 A03 2 2 2 VCC 2 2 2 2 A02 A01 A00 D00 D01 D02 -IOCS16 -CD2 -CD1 D11 D12 D13 D14 D15 1 1 1 1 1 1 D121 1 1 1 1 D12 -CE2 -CE2 -CS1 -VS1 -VS1 -VS1 Transcend Information Inc. 4 V1. 0 TS4G~32GCF150 TS4G~32GCF150 PC Card Memory Mode Pin Num 34 Signal Name -IORD 10 HSTROBE HDMARDY11 -IOWR STOP 10, 11 150X CompactFlash Card PC Card I/O Mode In, Out Type I3U Pin Num 34 Signal Name -IORD 10 HSTROBE -HDMARDY11 -IOWR STOP 10, 11 True IDE Mode4 In, Out Type I3U Pin Num 34 Signal Name -IORD 8 HSTROBE 9 -HDMARDY -IOWR STOP -WE 7 8, 9 7 Pin Type I Pin Type I Pin Type I In, Out Type I3Z 35 36 37 38 39 40 41 I I O I O I 10 I3U I3U OT1 Power I2Z OPEN I2Z 35 36 37 38 39 40 41 I I O I O I 10 I3U I3U OT1 Power I2Z OPEN I2Z 35 36 37 38 39 40 41 I I O I O I 8 I3Z I3U OZ1 Power I2U OPEN I2Z ON1 -WE READY VCC -CSEL -VS2 RESET -WAIT 5 -WE -IREQ VCC -CSEL -VS2 RESET -WAIT 5 3 INTRQ VCC -CSEL -VS2 -RESET IORDY 7 42 -DDMARDY DSTROBE O OT1 42 -DDMARDY DSTROBE O OT1 42 -DDMARDY DSTROBE O 11 11 9 OT1 13 43 44 45 46 47 48 49 50 -INPACK -DMARQ -REG -DMACK BVD2 BVD1 D08 1 12 12 O I O O I/O I/O I/O OT1 I3U OT1 OT1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground 43 44 45 46 47 48 49 50 -INPACK -DMARQ -REG DMACK 12 -SPKR -STSCHG D08 1 12 O I O O I/O I/O I/O OT1 I3U OT1 OT1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground 43 44 45 46 47 48 49 50 DMARQ -DMACK -DASP -PDIAG D08 1 6 O I I/O I/O I/O I/O I/O OZ1 I3U I1U, ON1 I1U, ON1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground D091 D10 1 D091 D10 1 D091 D10 1 GND GND GND Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state signals not to consume current. 2) The signal should be grounded by the host. 3) The signal should be tied to VCC by the host. [. . . ] Bit 6: LBA is a flag to select either Cylinder/Head/Sector (CHS) or Logical Block Address Mode (LBA). When LBA=0, Cylinder/Head/Sector mode is selected. When LBA=1, Logical Block Address is selected. In Logical Block Mode, the Logical Block Address is interpreted as follows: LBA7-LBA0: Sector Number Register D7-D0. LBA15-LBA8: Cylinder Low Register D7-D0. LBA23-LBA16: Cylinder High Register D7-D0. LBA27-LBA24: Drive/Head Register bits HS3-HS0. Bit 5: this bit is specified as 1 for backward compatibility reasons. It is intended that this bit will become obsolete in a future revisions of the specification. This bit is ignored by some controllers in some commands. Setting this bit to 1 is obsolete in PCMCIA modes of operation. If the obsolete functionality is support by a CF Storage Card, the CompactFlash Storage Card is set to be Card 0 or 1 using the copy field (Drive #) of the PCMCIA Socket & Copy configuration register. Transcend Information Inc. 52 V1. 0 TS4G~32GCF150 TS4G~32GCF150 150X CompactFlash Card Bit 3 (HS3): when operating in the Cylinder, Head, Sector mode, this is bit 3 of the head number. It is Bit 27 in the Logical Block Address mode. Bit 2 (HS2): when operating in the Cylinder, Head, Sector mode, this is bit 2 of the head number. It is Bit 26 in the Logical Block Address mode. Bit 1 (HS1): when operating in the Cylinder, Head, Sector mode, this is bit 1 of the head number. It is Bit 25 in the Logical Block Address mode. Bit 0 (HS0): when operating in the Cylinder, Head, Sector mode, this is bit 0 of the head number. It is Bit 24 in the Logical Block Address mode. Status & Alternate Status Registers (Address 1F7h[177h]&3F6h[376h]; Offsets 7 & Eh) These registers return the CompactFlash Storage Card status when read by the host. Reading the Status register does clear a pending interrupt while reading the Auxiliary Status register does not. The status bits are described as follows: Bit 7 (BUSY): the busy bit is set when the CompactFlash Storage Card has access to the command buffer and registers and the host is locked out from accessing the command register and buffer. [. . . ] When this bit is cleared, PC Card Memory and IO Modes are not supported by the device. Transcend Information Inc. 70 V1. 0 TS4G~32GCF150 TS4G~32GCF150 Idle - 97h or E3h 150X CompactFlash Card This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. If the sector count is non-zero, it is interpreted as a timer count with each count being 5 milliseconds and the automatic power down mode is enabled. If the sector count is zero, the automatic power down mode is disabled. Note that this time base (5 msec) is different from the ATA specification. Bit -> Command (7) C/D/H (6) Cyl High (5) Cyl Low (4) Sec Num (3) Sec Cnt (2) Feature (1) X 7 6 5 4 3 2 1 0 97h or E3h Drive X X X Timer Count (5 msec increments) X X Idle Immediate - 95h or E1h This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. Bit -> Command (7) C/D/H (6) Cyl High (5) Cyl Low (4) Sec Num (3) Sec Cnt (2) Feature (1) X 7 6 5 4 3 2 1 0 95h or E1h Drive X X X X X X Initialize Drive Parameters - 91h This command enables the host to set the number of sectors per track and the number of heads per cylinder. [. . . ]