User manual TRANSCEND TS16GUSDHC6-P3 DATASHEET

[. . . ] The given minimum frequency range is for cases were continues clock is required Transcend Information Inc. 7 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 · Bus Timing (High Speed Mode) 4~16 GB microSDHC Class 6 Card + Reader P3 Parameter Clock frequency Data Transfer Mode Clock low time Clock high time Clock rise time Clock fall time Inputs CMD, DAT (referenced to CLK) Input set-up time Input hold time Outputs CMD, DAT (referenced to CLK) Symbol fPP tWL tWH tTLH tTHL tISU tIH Min 0 7 7 Max. 50 Unit MHz ns ns Remark CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) Clock CLK (All values are referred to min (VIH) and max (VIL) 3 3 6 2 ns ns ns ns Transcend Information Inc. 8 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 Output Delay time during Data Transfer Mode Output Hold time 1 4~16 GB microSDHC Class 6 Card + Reader P3 tODLY tOH 2. 5 40 14 ns ns pF CL 40 pF, (1 card) CL 40 pF, (1 card) (1 card) Total System capacitance for each line CL 1) In order to satisfy severe timing, host shall drive only one card. Transcend Information Inc. 9 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 Reliability and Durability Temperature 4~16 GB microSDHC Class 6 Card + Reader P3 Operation: -25°C / 85°C Storage: -40°C (168h) / 85°C (500h) Junction temperature: max. hum. /500h Salt Water Spray: 3% NaCl/35C; 24h acc. MIL STD Method 1009 10. 000 mating cycles; test procedure: tbd. 10N 0. 15N. m or +/-2. 5 deg 1. 5m free fall UV: 254nm, 15Ws/cm² according to ISO 7816-1 0. 1 Gy of medium-energy radiation (70 keV to 140 keV, cumulative dose per year) to both sides of the card, according to ISO7816-1. [. . . ] This procedure is established to ensure uniqueness of the CID register. · OID A 2-character ASCII string that identifies the card OEM and/or the card contents (when used as a distribution media either on ROM or FLASH cards). The OID number is controlled, defined, and allocated to a SD Memory Card manufacturer by the SD-3C, LLC. This procedure is established to ensure uniqueness of the CID register. Note: SD-3C, LLC licenses companies that wish to manufacture and/or sell SD Memory Cards, including but not limited to flash memory, ROM, OTP, RAM, and SDIO Combo Cards. SD-3C, LLC is a limited liability company established by Matsushita Electric Industrial Co. Ltd. , SanDisk Corporation and Toshiba Corporation. · PNM The product name is a string, 5 ASCII characters long. · PRV Transcend Information Inc. 12 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 4~16 GB microSDHC Class 6 Card + Reader P3 The product revision is composed of two Binary Coded Decimal (BCD) digits, four bits each, representing an "n. m" revision number. The "n" is the most significant nibble and "m" is the least significant nibble. As an example, the PRV binary value field for product revision "6. 2" will be: 0110 0010 · PSN The Serial Number is 32 bits of binary number. · MDT The manufacturing date composed of two hexadecimal digits, one is 8 bit representing the year(y) and the other is four bits representing the month(m). The "m" field [11:8] is the month code. The "y" field [19:12] is the year code. As an example, the binary value of the Date field for production date "April 2001" will be: 00000001 0100. · CRC CRC7 checksum (7 bits). 3. CSD Register Table 5-16 shows Definition of the CSD for the High Capacity SD Memory Card (CSD Version 2. 0). The following sections describe the CSD fields and the relevant data types for the High Capacity SD Memory Card. CSD Version 2. 0 is applied to only the High Capacity SD Memory Card. The field name in parenthesis is set to fixed value and indicates that the host is not necessary to refer these fields. If set, a driver stage register (DSR)must be implemented also. Transcend Information Inc. 16 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 4~16 GB microSDHC Class 6 Card + Reader P3 · C_SIZE This field is expanded to 22 bits and can indicate up to 2 TBytes (It is the same as the maximum memory space specified by a 32-bit block address. ) This parameter is used to calculate the user data area capacity in the SD memory card (not include the protected area). The user data area capacity is calculated from C_SIZE as follows: memory capacity = (C_SIZE+1) * 512K byte As the maximum capacity of the Physical Layer Specification Version 2. 00 is 32 GB, the upper 6 bits of this field shall be set to 0. · ERASE_BLK_EN This field is fixed to 1, which means the host can erase one or multiple units of 512 bytes. · SECTOR_SIZE This field is fixed to 7Fh, which indicates 64 KBytes. This value does not relate to erase operation. Version 2. 00 cards indicates memory boundary by AU size and this field should not be used. · WP_GRP_SIZE This field is fixed to 00h. The High Capacity SD Memory Card does not support write protected groups. · WP_GRP_ENABLE This field is fixed to 0. The High Capacity SD Memory Card does not support write protected groups. · R2W_FACTOR This field is fixed to 2h, which indicates 4 multiples. Write timeout can be calculated by multiplying the read access time and R2W_FACTOR. However, the host should not use this factor and should use 250 ms for write timeout · WRITE_BL_LEN This field is fixed to 9h, which indicates WRITE_BL_LEN=512 Byte. · WRITE_BL_PARTIAL This field is fixed to 0, which indicates partial block read is inhibited and only unit of block access is allowed. · FILE_FORMAT_GRP This field is set to 0. [. . . ] In the case of High Capacity SD Memory Card, this field shall be set to 3 (Version 2. 00). · SD_BUS_WIDTHS Describes all the DAT bus widths that are supported by this card. Since SD Memory Card shall support at least the two bus modes 1bit or 4bit width then any SD Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101"). Transcend Information Inc. 21 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 Mechanical Dimension 4~16 GB microSDHC Class 6 Card + Reader P3 Mechanical Description: Top View Transcend Information Inc. 22 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 4~16 GB microSDHC Class 6 Card + Reader P3 Mechanical Description: Bottom View Transcend Information Inc. 23 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 4~16 GB microSDHC Class 6 Card + Reader P3 Mechanical Description: Keep Out Area Transcend Information Inc. 24 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 4~16 GB microSDHC Class 6 Card + Reader P3 microSD package: Dimensions Transcend Information Inc. 25 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 Description RDP3 is a USB2. 0 Compact Card Reader. It is designed for fast, easy data transfer and exchange using microSD Memory Card. 4~16 GB microSDHC Class 6 Card + Reader P3 Placement Features · Fully Compliant with the Hi-Speed USB 2. 0 specification · USB powered (no external power or battery needed) · Support the microSD Memory Card insertion directly System Requirements · Desktop or notebook computer with a working USB port · One of the following Operating Systems: O O O O O O Windows® Me Windows® 2000 Windows® XP Windows VistaTM MacTM OS 9. 0, or later LinuxTM Kernel 2. 4, or later Dimensions Side A B C Millimeters 32. 80 ± 1. 0 16. 00 ± 1. 0 7. 80 ± 1. 0 Inches 1. 29 ± 0. 04 0. 63 ± 0. 04 0. 31 ± 0. 04 Transcend Information Inc. 26 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 USB Pinouts Pin No. 01 02 03 04 Pin Name VUSB DD+ VSS 4~16 GB microSDHC Class 6 Card + Reader P3 USB Pin Identification Symbol DD+ Function USB differential signal: The pairs are used to transmit Data/Address/Command VSS VUSB Ground USB Power Input Block Diagram Controller USB Port VOUT VUSB 5-3. 3/3. 3-1. 8V Voltage Regulator MicroSD slot 12MHz CRYST Transcend Information Inc. 27 TS4~16GUSDHC6-P3 TS4~16GUSDHC6-P3 Recommended Operating Conditions: SYMBOL VUSB TOPR PARAMETER Power Supply Operating Temperature MIN. 4. 5 0 4~16 GB microSDHC Class 6 Card + Reader P3 TYP. [. . . ]