User manual TRANSCEND TS2GCF133 DATASHEET

[. . . ] TS1G~32GCF133 TS1G~32GCF133 Description The Transcend CF 133X is a High Speed Compact Flash Card with high quality Flash Memory assembled on a printed circuit board. 133X CompactFlash Card Features · CompactFlash Specification Version 4. 1 Complaint · RoHS compliant products · Single Power Supply: 3. 3V±5% or 5V±10% · Operating Temperature: -25oC to 85oC · Storage Temperature: -40oC to 85oC · Operating Humidity (Non condensation): 0% to 95% · Storage Humidity (Non condensation): 0% to 95% · Operation Modes: PC Card Memory Mode PC Card IO Mode True IDE Mode · True IDE Mode supports: Ultra DMA Mode 0 to Mode 4 MultiWord DMA Mode 0 to Mode 4 PIO mode 0 to mode 6 · True IDE mode: Removable Disk (Standard) · PC Card Mode: Removable Disk (Standard) · Durability of Connector: 10, 000 times · Support S. M. A. R. T (Self-defined) · Support Security Command · Support Wear-Leveling to extend product life · Compliant to CompactFlash, PCMCIA, and ATA standards Placement Dimensions Transcend Information Inc. 1 TS1G~32GCF133 TS1G~32GCF133 133X CompactFlash Card Transcend Transcend Information Inc. 2 TS1G~32GCF133 TS1G~32GCF133 Block Diagram 133X CompactFlash Card Transcend Information Inc. 3 TS1G~32GCF133 TS1G~32GCF133 Pin Assignments and Pin Type 133X CompactFlash Card Transcend Information Inc. 4 TS1G~32GCF133 TS1G~32GCF133 133X CompactFlash Card Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state signals not to consume current. 2) The signal should be grounded by the host. 3) The signal should be tied to VCC by the host. [. . . ] This bit is set to 0 at power on and Reset. Bit 0: this bit is ignored by the CompactFlash Storage Card. Transcend Information Inc. 50 TS1G~32GCF133 TS1G~32GCF133 Card (Drive) Address Register (Address 3F7h[377h]; Offset Fh) 133X CompactFlash Card This register is provided for compatibility with the AT disk drive interface. It is recommended that this register not be mapped into the host's I/O space because of potential conflicts on Bit 7. Bit 7: this bit is unknown. Implementation Note: Conflicts may occur on the host data bus when this bit is provided by a Floppy Disk Controller operating at the same addresses as the CompactFlash Storage Card. Following are some possible solutions to this problem for the PCMCIA implementation: 1) Locate the CompactFlash Storage Card at a non-conflicting address, i. e. Secondary address (377) or in an independently decoded Address Space when a Floppy Disk Controller is located at the Primary addresses. 2) Do not install a Floppy and a CompactFlash Storage Card in the system at the same time. 3) Implement a socket adapter that can be programmed to (conditionally) tri-state D7 of I/0 address 3F7h/377h when a CompactFlash Storage Card is installed and conversely to tristate D6-D0 of I/O address 3F7h/377h when a floppy controller is installed. 4) Do not use the CompactFlash Storage Card's Drive Address register. This may be accomplished by either a) If possible, program the host adapter to enable only I/O addresses 1F0h-1F7h, 3F6h (or 170h-177h, 176h) to the CompactFlash Storage Card or b) if provided use an additional Primary / Secondary configuration in the CompactFlash Storage Card which does not respond to accesses to I/O locations 3F7h and 377h. With either of these implementations, the host software shall not attempt to use information in the Drive Address Register. Bit 6 (-WTG): this bit is 0 when a write operation is in progress; otherwise, it is 1. Bit 5 (-HS3): this bit is the negation of bit 3 in the Drive/Head register. Bit 4 (-HS2): this bit is the negation of bit 2 in the Drive/Head register. Bit 3 (-HS1): this bit is the negation of bit 1 in the Drive/Head register. Bit 2 (-HS0): this bit is the negation of bit 0 in the Drive/Head register. Bit 1 (-nDS1): this bit is 0 when drive 1 is active and selected. Bit 0 (-nDS0): this bit is 0 when the drive 0 is active and selected. Transcend Information Inc. 51 TS1G~32GCF133 TS1G~32GCF133 CF-ATA Command Set 133X CompactFlash Card CF-ATA Command Set summarizes the CF-ATA command set with the paragraphs that follow describing the individual commands and the task file for each. Command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Check Power Mode Execute Drive Diagnostic Erase Sector Flush Cache Format Track Identify Device Idle Idle Immediate Initialize Drive Parameters Key Management Structure Read Key Management Read Keying Material Key Management Change Key Management Value NOP Read Buffer Read DMA Read Long Sector Read Multiple Read Sector(s) Read Verify Sector(s) Recalibrate Request Sense Security Disable Password Security Erase Prepare Security Erase Unit Security Freeze Lock Security Set Password Security Unlock Seek Code E5 or 98h 90h C0h E7h 50h ECh E3h or 97h E1h or 95h 91h B9 (Feature 0-127) B9 (Feature 80) B9 (Feature 81) 00h E4h C8h 22h or 23h C4h 20h or 21h 40h or 41h 1Xh 03h F6h F3h F4h F5h F1h F2h 7Xh FR ­ ­ ­ ­ ­ ­ ­ ­ ­ Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ ­ SC ­ ­ Y ­ Y ­ Y ­ Y Y Y Y ­ ­ Y SN ­ ­ Y ­ ­ ­ ­ ­ ­ Y Y Y ­ ­ Y Y Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ Y CY ­ ­ Y ­ Y ­ ­ ­ ­ Y Y Y ­ ­ Y Y Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ Y DH Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ Y LBA ­ ­ Y ­ Y ­ ­ ­ ­ ­ ­ ­ ­ ­ Y Y Y Y Y Status Support Support Support NOT Support Support Support Support Support Support NOT Support NOT Support NOT Support NOT Support Support Support NOT Support Support Support Support Support Support Support Support Support Support Support Support Support #2 #2 #2 #2 #2 #2 #3 #1 #1 #1 #3 Note Transcend Information Inc. 52 TS1G~32GCF133 TS1G~32GCF133 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Set Feature Set Multiple Mode Set Sleep Mode Standby Standby Immediate Translate Sector Wear Level Write Buffer Write DMA Write Long Sector Write Multiple Write Multiple w/o Erase Write Sector(s) Write Sector(s) w/o Erase Write Verify EFh C6h E6h or 99h E2 or 96h E0 or 94h 87h F5h E8h CAh 32h or 33h C5h CDh 30h or 31h 38h 3Ch Y ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ Y ­ ­ ­ Y ­ ­ Y ­ Y Y Y Y Y ­ ­ ­ ­ ­ Y ­ ­ Y Y Y Y Y Y Y ­ ­ ­ ­ ­ Y ­ ­ Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y ­ ­ ­ ­ ­ Y ­ ­ Y Y Y Y Y Y Y 133X CompactFlash Card Support Support Support Support Support Support Support Support Support Not Support Support Support Support Support Support #3 #1: This command is optional, depending on the key Management scheme in use. #2: Use of this command is not recommended by CFA #3: Use of this command is not recommended. #4: When the controller gets this command, it will skip this command and return 0x50. Definitions FR = Features Register SC =Sector Count register (00H to FFH, 00H means 256 sectors) SN = Sector Number register CY = Cylinder Low/High register DH = Head No. (0 to 15) of Drive/Head register LBA = Logic Block Address Mode Support ­ = Not used for the command Y = Used for the command Transcend Information Inc. 53 TS1G~32GCF133 TS1G~32GCF133 133X CompactFlash Card Definitions: FR = Features Register SC = Sector Count RegisterS SN = Sector Number Register CY = Cylinder Registers DH = Card/Drive/Head Register LBA = Logical Block Address Mode Supported (see command descriptions for use). Y - The register contains a valid parameter for this command. [. . . ] Value 0 1 2 3 4-7 Maximum PCMCIA IO timing mode Supported 255ns Cycle PCMCIA I/O Mode 120ns Cycle PCMCIA I/O Mode 100ns Cycle PCMCIA I/O Mode 80ns Cycle PCMCIA I/O Mode Reserved Bits 5-3: Maximum Memory timing mode supported Indicates the Maximum Memory timing mode supported by the card. Value 0 1 2 3 4-7 Maximum Memory timing mode Supported 250ns Cycle Memory Mode 120ns Cycle Memory Mode 100ns Cycle Memory Mode 80ns Cycle Memory Mode Reserved Idle - 97h or E3h This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. If the sector count is non-zero, it is interpreted as a timer count with each count being 5 milliseconds and the automatic power down mode is enabled. If the sector count is zero, the automatic power down mode is disabled. [. . . ]