User manual TRANSCEND TS4GSDHC6- P2 DATASHEET

[. . . ] The SD Memory Card guarantees its bus timing when total bus capacitance is less than maximum value of CL (40 pF). 4 Transcend Information Inc. TS4G-32GSDHC6-P2 · Bus Signal Levels SDHC Memory Card + Reader P2 As the bus can be supplied with a variable supply voltage, all signal levels are related to the supply voltage. To meet the requirements of the JEDEC specification JESD8-1A and JESD8-7, the card input and output voltages shall be within the following specified ranges for any VDD of the allowed voltage range: Parameter Output HIGH voltage Output LOW voltage Input HIGH voltage Input LOW voltage Symbol VOH VOL VIH VIL Min. 0. 75* VDD Max. 0. 125* VDD Unit V V V V Remark IOH = -100 µA @VDD min IOL = -100 µA @VDD min 0. 625* VDD VSS ­ 0. 3 VDD + 0. 3 0. 25* VDD 5 Transcend Information Inc. TS4G-32GSDHC6-P2 · Bus Timing SDHC Memory Card + Reader P2 Parameter Clock frequency Data Transfer Mode Clock frequency Identification Mode Clock low time Clock high time Clock rise time Clock fall time Inputs CMD, DAT (referenced to CLK) Input set-up time Input hold time Outputs CMD, DAT (referenced to CLK) Symbol fPP fOD tWL tWH tTLH tTHL tISU tIH Min 0 0(1)/100 10 10 Max. 25 400 Unit MHz KHz ns ns Remark CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) Clock CLK (All values are referred to min (VIH) and max (VIL) 10 10 5 5 ns ns ns ns 6 Transcend Information Inc. TS4G-32GSDHC6-P2 Output Delay time during Data Transfer Mode tODLY 0 14 SDHC Memory Card + Reader P2 ns CL 40 pF, (1 card) Output Delay time during Identification Mode tODLY 0 50 ns CL 40 pF, (1 card) (1) 0 Hz means to stop the clock. The given minimum frequency range is for cases were continues clock is required 7 Transcend Information Inc. TS4G-32GSDHC6-P2 · Bus Timing (High Speed Mode) SDHC Memory Card + Reader P2 Parameter Clock frequency Data Transfer Mode Clock low time Clock high time Clock rise time Clock fall time Inputs CMD, DAT (referenced to CLK) Input set-up time Input hold time Outputs CMD, DAT (referenced to CLK) Symbol fPP tWL tWH tTLH tTHL tISU tIH Min 0 7 7 Max. 50 Unit MHz ns ns Remark CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) CCARD 10 pF, (1 card) Clock CLK (All values are referred to min (VIH) and max (VIL) 3 3 6 2 ns ns ns ns 8 Transcend Information Inc. TS4G-32GSDHC6-P2 Output Delay time during Data Transfer Mode Output Hold time 1 SDHC Memory Card + Reader P2 tODLY tOH 2. 5 40 14 ns ns pF CL 40 pF, (1 card) CL 40 pF, (1 card) (1 card) Total System capacitance for each line CL 1) In order to satisfy severe timing, host shall drive only one card. 9 Transcend Information Inc. TS4G-32GSDHC6-P2 Reliability and Durability Temperature Operation: -25° / 85° C C Storage: -40° (168h) / 85° (500h) C C Junction temperature: max. 95° C Moisture and corrosion Operation: 25° / 95% rel. humidity C SDHC Memory Card + Reader P2 Storage: 40° / 93% rel. [. . . ] The MID number is controlled, defined, and allocated to a SD Memory Card manufacturer by the SD-3C, LLC. This procedure is established to ensure uniqueness of the CID register. · OID A 2-character ASCII string that identifies the card OEM and/or the card contents (when used as a distribution media either on ROM or FLASH cards). The OID number is controlled, defined, and allocated to a SD Memory Card manufacturer by the SD-3C, LLC. This procedure is established to ensure uniqueness of the CID register. Note: SD-3C, LLC licenses companies that wish to manufacture and/or sell SD Memory Cards, including but not limited to flash memory, ROM, OTP, RAM, and SDIO Combo Cards. SD-3C, LLC is a limited liability company established by Matsushita Electric Industrial Co. Ltd. , SanDisk Corporation and Toshiba Corporation. · PNM The product name is a string, 5 ASCII characters long. 21 Transcend Information Inc. TS4G-32GSDHC6-P2 · PRV SDHC Memory Card + Reader P2 The product revision is composed of two Binary Coded Decimal (BCD) digits, four bits each, representing an "n. m" revision number. The "n" is the most significant nibble and "m" is the least significant nibble. As an example, the PRV binary value field for product revision "6. 2" will be: 0110 0010 · PSN The Serial Number is 32 bits of binary number. · MDT The manufacturing date composed of two hexadecimal digits, one is 8 bit representing the year(y) and the other is four bits representing the month(m). The "m" field [11:8] is the month code. The "y" field [19:12] is the year code. As an example, the binary value of the Date field for production date "April 2001" will be: 00000001 0100. · CRC CRC7 checksum (7 bits). 3. CSD Register Table 5-16 shows Definition of the CSD for the High Capacity SD Memory Card (CSD Version 2. 0). The following sections describe the CSD fields and the relevant data types for the High Capacity SD Memory Card. CSD Version 2. 0 is applied to only the High Capacity SD Memory Card. The field name in parenthesis is set to fixed value and indicates that the host is not necessary to refer these fields. The fixed values enables host, which refers to these fields, to keep compatibility to CSD Version 1. 0. If set, a driver stage register (DSR)must be implemented also. 61 Transcend Information Inc. TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 · C_SIZE This field is expanded to 22 bits and can indicate up to 2 TBytes (It is the same as the maximum memory space specified by a 32-bit block address. ) This parameter is used to calculate the user data area capacity in the SD memory card (not include the protected area). The user data area capacity is calculated from C_SIZE as follows: memory capacity = (C_SIZE+1) * 512K byte As the maximum capacity of the Physical Layer Specification Version 2. 00 is 32 GB, the upper 6 bits of this field shall be set to 0. · ERASE_BLK_EN This field is fixed to 1, which means the host can erase one or multiple units of 512 bytes. · SECTOR_SIZE This field is fixed to 7Fh, which indicates 64 KBytes. This value does not relate to erase operation. Version 2. 00 cards indicates memory boundary by AU size and this field should not be used. · WP_GRP_SIZE This field is fixed to 00h. The High Capacity SD Memory Card does not support write protected groups. · WP_GRP_ENABLE This field is fixed to 0. The High Capacity SD Memory Card does not support write protected groups. · R2W_FACTOR This field is fixed to 2h, which indicates 4 multiples. [. . . ] In the case of High Capacity SD Memory Card, this field shall be set to 3 (Version 2. 00). · SD_BUS_WIDTHS Describes all the DAT bus widths that are supported by this card. Since SD Memory Card shall support at least the two bus modes 1bit or 4bit width then any SD Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101"). 12 Transcend Information Inc. TS4G-32GSDHC6-P2 Mechanical Dimension SDHC Memory Card + Reader P2 22 Transcend Information Inc. TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 32 Transcend Information Inc. TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 42 Transcend Information Inc. TS4G-32GSDHC6-P2 Description TS-RDP2 is a USB2. 0 Portable SD/MMC Card Reader. It is a small and thin device specifically designed for fast, easy data transfer and exchange using multiple types of Memory Cards. SDHC Memory Card + Reader P2 Placement Features · Color: White · Fully Compliant with the Hi-Speed USB 2. 0 specification · Hi-Speed Data transfer rates of up to 480Mb/s · USB powered (no external power or battery needed) · LED indicates card insertion and data traffic · Compatible Cards Directly: O O O O O O Dimensions Side A Millimeters 57. 80 ± 1. 0 23. 10 ± 1. 0 8. 40 ± 1. 0 Inches 2. 28 ± 0. 04 0. 91 ± 0. 04 0. 33 ± 0. 04 SD (Secure Digital) SDHC (Secure Digital High Capacity) MMC (MultiMediaCard) MMCplus MMCmobile RS-MMC O B C System Requirements Desktop or notebook computer with a working USB port One of the following Operating Systems: Windows Me Windows 2000 Windows XP Windows Vista Windows 7 Mac OS 9. x, or later Linux Kernel 2. 4. 2, or later TM TM ® TM ® ® ® Adapter Required O O O O O O miniSD O miniSDHC O microSDHC O microSD / TransFlash O MMCmicro O Transcend Information, Inc. 25 TS4G-32GSDHC6-P2 Pinouts Pin No. 01 02 03 04 Pin Name VUSB USBUSB+ VSS VSS VUSB USBUSB+ SDHC Memory Card + Reader P2 Pin Identification Symbol Function USB differential signal: The pairs are used to transmit Data/Address/Command Ground USB Power Input Block Diagram Controller USB Port VUSB 3. 3V/1. 8V Voltage Regulator 12MHz Crystal VD33P VDD18 VDDHM VOUT VIN SD/MMC slot Transcend Information, Inc. 26 TS4G-32GSDHC6-P2 Recommended Operating Conditions: SYMBOL VUSB TOPR PARAMETER Power Supply Operating Temperature MIN. 5. 0 SDHC Memory Card + Reader P2 MAX. [. . . ]