User manual TRAYNOR @DG65R

[. . . ] The apparatus should not be exposed to dripping or splashing water; no objects filled with liquids should be placed on the apparatus. Terminals marked with the "lightning bolt" are hazardous live; the external wiring connected to these terminals require installation by an instructed person or the use of ready made leads or cords. No naked flame sources, such as lighted candles, should be placed on the apparatus. The unit should be serviced only by qualified service personnel. [. . . ] The Gain control is used to adjust the amount of overdrive, while the Volume control allows you to set the actual loudness of the amplifier. Boost Switch 3 4 The boost circuit enables you to achieve `a-bit-more' overdrive for leads when needed. The Boost can be selected via the front panel switch or through the supplied footswitch pedal. a red LED illuminates to indicate when the boost is active. Channel 1 Tone Controls 6 The Treble, Bass, and Middle tone controls are used to help shape your sound. These are active only when Channel 1 is selected. When channel 2 is active the green LED located next to the Channel 2 Volume control is illuminated. Brightness Switch 10 Channel 2 includes a Brightness switch that activates circuitry providing an additional treble boost, which helps make your tone sparkle. Master Control 13 This Master control not only Treble 5 adjusts the overall volume Middle level of the DG65D/DG65R 5 but also provides control Bass 0 10 of the output power. The 5 DG65's power amplifier has 0 10 been designed to behave akin to a "tube" power 0 10 amplifier stage and will provide the same level of compression and soft clipping at all volume levels. The dial has been calibrated to let you know how many watts you're working with. Contour Control 12 The Contour control adjusts the amount of mid-scoop, which allows you to dial-in character to your tone from vintage to modern, and all points in between. The reverb is only changed in the 4 Special effects but remains unchanged for all other effects. Reverb Control (DG65R only) 14 The Reverb control adjusts the overall reverb level for both channels. the DG65R is equipped POWER with a long-style Effects Reverb PHONES Level Level Accutronics® dualspring reverb for EFFECTS SELECT authentic vintage reverb. The DG65D is equipped with a 24-bit DSP based effects processor for lush large room reverb and effects. EFX / Line Preamp Out & Amp In Jacks 21 The Preamp Out and Amp In jacks of the DG65 allow convenient use of an external effects unit. Simply connect a ¼-inch phone cable to the Preamp Out jack and connect this cable to the input of your effects unit. To send the processed signal back to the DG65, connect the output of the effects unit to the Amp In jack of the DG65. Preamp Out jack can also be used as a direct line out. [. . . ] If you disconnect the internal 12-inch Eminence Red Coat® speaker by depressing the Internal Speaker Defeat switch, you can connect up to two 8-ohm external cabinets (minimum speaker load of 4-ohms). Impedance (Watts) Minimum Impedance (ohms) Burst Power - 2 cycle Speaker Configuration - LF (Size / Power) Input Channels Channel 1 - inputs Channel 1 - controls Channel 1 - switches Channel 2 - inputs Channel 2 - controls Channel 2 - switches Channel Switching Master Volume Control Main Tone Controls Input Sensitivity (mV) Master Outputs Line Out (type / configuration) Line Out Sensitivity (Vrms) Effects Volume Effects Loop / Location Effects Footswitch / Function Effects Return Sensitivity (Vrms) Internal Reverb / Effects LED Indicators Protection External speaker output / location Headphone Jack Other Features 65 8 65 4 85-watts 12 inch / 75 Watts Hi / Lo 1/4 inch phone Gain, Volume, Treble, Bass, Middle Boost Shares ch 1 input Gain, Volume, Treble, Bass, Middle Bright Yes / Footswitchable Yes Contour 20 Preamp Out / Headphone Out 1/4 inch TRS / Rear (Effects Send) 300mV Reverb / Effects Post Preamp / Rear Yes / Channel Select, Boost 300mV 16 Preset DSP, Seperate Digital Reverb Channel Select, Boost, Power Short Circuit, Thermal 1/4-inch, Rear / Internal Speaker Defeat Switch Yes / Front Panel / Dyna-Sound Speaker Emulation North American Made 3-Stage Dyanamic Tube Emulation Transconductance Power Amplifier for further tube All Plywood Contruction Perforated Steel Grille Dimensions (DWH, inches) Dimensions (DWH, cm) Weight (lbs / kg) 10 x 23. Impedance (Watts) Minimum Impedance (ohms) Burst Power - 2 cycle Speaker Configuration - LF (Size / Power) Input Channels Channel 1 - inputs Channel 1 - controls Channel 1 - switches Channel 2 - inputs Channel 2 - controls Channel 2 - switches Channel Switching Master Volume Control Main Tone Controls Input Sensitivity (mV) Master Outputs Line Out (type / configuration) Line Out Sensitivity (Vrms) Effects Volume Effects Loop / Location Effects Footswitch / Function Effects Return Sensitivity (Vrms) Internal Reverb / Effects LED Indicators Protection External speaker output / location Headphone Jack 65 8 65 4 85-watts 12 inch / 75 Watts Hi / Lo 1/4 inch phone Gain, Volume, Treble, Bass, Middle Boost Shares ch 1 input Gain, Volume, Treble, Bass, Middle Bright Yes / Footswitchable Yes Contour 20 Preamp Out / Headphone Out 1/4 inch TRS / Rear (Effects Send) 300mV Reverb Post Preamp / Rear Yes / Channel Select, Boost 300mV Accutronics Spring Reverb Channel Select, Boost, Power Short Circuit, Thermal 1/4-inch, Rear / Internal Speaker Defeat Switch Yes / Front Panel / Dyna-Sound Speaker Emulation North American Made 3-Stage Dyanamic Tube Emulation Other Features Transconductance Power Amplifier for further tube All Plywood Contruction Perforated Steel Grille Dimensions (DWH, inches) Dimensions (DWH, cm) Weight (lbs / kg) 10 x 23. Unlimited Warranty Yorkville's two and ten-year unlimited warranty on this product is transferable and does not require registration with Yorkville Sound or your dealer. [. . . ]