User manual TREK BIKES INCITE 6I-8I 2005

[. . . ] TREK INCITE Bicycle Computer Owner's Manual This manual explains the installation and use of several Trek bicycle computer models: · Incite 6i Incite 8i · Incite 9i Incite 11i Please read this manual carefully and save it for future reference. If you do not understand the information in this manual, or you have a question about your Incite computer that this manual does not cover, consult your Trek dealer. If you have a question or problem that your Trek dealer can't handle, contact us at: Trek Bicycle Corporation Attn: Customer Service 801 W. Madison Street Waterloo, Wisconsin 53594 http://www. [. . . ] If the computer shows current speed, the sensor is reading the magnet. If the computer is not displaying current speed, realign the sensor and magnet until current speed is displayed. Tighten the nylon ties and trim the excess length (Figure 12). Figure 9- Extra wire wrapped around the brake housing 1. 0 3. 0mm Figure 10- Magnet alignment and clearance Figure 11- Wireless sensor, foot, and fork blade Figure 12- Trim excess nylon tie length Installation 3 SETTING THE COMPUTER The computer must be set, or "programmed, " so that it gives its readout in the units preferred by the user, and so that it calculates with the correct wheel size. There are three ways to use the buttons: · Push- touch once · Cycle- push repeatedly as needed · Hold- push and hold in for two or three seconds The method used to set the computer varies according to the computer model. Follow the instructions covering your computer model, grouped as follows: · Incite 6i and 8i (pages 7-9) · Incite 9i and 11i (pages 10-12) INCITE 6I AND 8I Setting the 6i and 8i is done by pushing the two buttons in a specific sequence. The button on the side of the computer is the Set button. The large button on the bottom, which may look like two buttons, is the Mode button. To set Odometer and Wheel size By default, the odometer always starts at `0'. If desired, the odometer can be manually set at another value. Push Mode to select measurement conversion. For a custom wheel size, see To set a custom wheel size 6. Cycle Set for the first digit of Odometer. Repeat steps 7 and 8 to select the other digits of Odometer. The computer returns to current speed. To set Custom wheel size 1. Push Mode to select measurement conversion. Cycle Set to the four-digit number (see Table 2). Table 2- Wheel size and corresponding settings in millimeters 700 x 20 700 x 23 700 x 25 700 x 28 700 x 32 700 x 35 700 x 38 2086 2096 2105 2136 2155 2168 2180 26 x 1. 5 26 x 1. 90 26 x 1. 95 26 x 2. 0 26 x 2. 1 26 x 2. 2 Custom 2010 2045 2050 2055 2068 2075 0000 - 2999 6. Cycle Set to your preferred value for the digit. Repeat steps 7 and 8 to select the other three digits. Cycle Set for the first digit of Odometer. Repeat steps 10 and 11 to select the other digits of Odometer. The computer returns to current speed display. Setting the computer 4 To set Clock 1. The computer returns to current speed. To Restart the trip modes The trip modes include TRP AVG, TME, and MAX. This operation sets all four values to zero, allowing , the computer to display information for a single ride. [. . . ] When purchasing a new battery, it is best to take the old battery with you. However, this is the generic description for the proper battery: CR2032, lithium cell, 3 volts To replace the battery 1. Identify the battery cover, with its deep slot. Insert a large coin into the slot and rotate in a counter-clockwise direction about one-quarter turn (Figure 14). [. . . ]