User manual TRENDNET TBW-103UB

[. . . ] Connect the equipment into an outlet on a circuit different from that To which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation IMPORTANT NOTE: FCC Radiation Exposure Statement This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2. 1093 paragraph (d)(2). [. . . ] Record the number of RX frames on the filed of "RX Frame". 6 - TBW-103UB User's Guide 4. 3 More Setting Click "More Setting " of Figure 4-1 to enter "More setting " window. The window is shown as "Figure 4-2". 4. 3. 1 "General Connection Setting" group: - Read the current status from the group if the "Change" button is not pressed. Select which key set will be use by the field of "Default Key ID" Modify the 4 sets key depending on the selected key length on the field of "Key Value". The key value is used the hexadecimal format. - 8 TBW-103UB User's Guide Figure 4-3 4. 3. 3 "Profile" group: - Select the profile(Figure 4-2) that has been saved previously from the "Profile name" drop down menu, then press "Load " button to load the status to use. - Write the profile name on the field of "Profile name", and press the "Save Current" button to save the current status on the profile. Select the profile name that wanted to delete from the "Profile name" drop down menu, and press "Delete" button to delete it Figure 4-4 9 TBW-103UB User's Guide Chapter 5 How to use the Wireless Utility(Access Point) 5. 1 Introduction To set your TBW-103UB as an Access Point (AP) , reference In Access Point mode , your TBW-103UB as an AP. This allows you to set up your wireless network without using a dedicate AP device. Up to 16 wireless station can associate to TBW-103UB. Additional Setup Requirement To bridge wireless and wired using the TBW-103UB, The following requirement must be met. The TBW-103UB must be installed a computer connect to the wired network. Either configure network sharing or bridge the two interfaces (Wireless & Wired) on the computer. Set the wireless station's IP address to be in the same subnet as the computer in which TBW-103UB is installed. 5. 2 The 802. 11g Wireless Utility Screen 5. 2. 1 Select "ACCESS POINT" in the MODE field to display the screen as shown. ACCESS POINT Mode 5. 2. 2 click "More Setting. . . "in the TBW-103UB screen to display the screen as shown. 10 TBW-103UB User's Guide 11 TBW-103UB User's Guide Chapter 6 How to use the Bluetooth Utility 6. 1 Open Bluetooth Utility Double-click the Bluetooth icon to launch the application and open the configuration tools dialog box to configure your adapter. 6. 2 Local Bluetooth Device The Local Bluetooth enabled device, known as "My Device", represents the user's computer that is running BlueSoleil. Operations: Hover mouse to display the local Bluetooth device's name or address (if without name). Click on the red ball to start or stop searching for Bluetooth devices in range. Right-click on the red ball to display a pop-up menu of related operations (e. g. , General Inquiry, My Services, Security, etc. ). 6. 3 Remote Bluetooth Devices Remote devices are other Bluetooth enabled devices that are in the Bluetooth radio range of your local device. BlueSoleil uses different icons to indicated different types of remtoe devices. 12 TBW-103UB User's Guide Icon Meanings Remote devices can be in any of three states, which BlueSoleil indicates with different colors. The device is connected to your computer. Operations Single-click on the icon to select. · · Double-click on the icon to search for the services supports by the remote Bluetooth device . Right-click on the icon to display a pop-up menu of related operations (e. g. [. . . ] Products returned to TRENDware must be pre-authorized by TRENDware with RMA number marked on the outside of the package, and sent prepaid, insured and packaged appropriately for safe shipment. WARRANTIES EXCLUSIVE: IF THE TRENDWARE PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDWARE'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDWARE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDWARE'S PRODUCTS. [. . . ]