User manual TRENDNET TE100-DX4PCI

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Section 4 Drivers Installation . . . . . . . . . . . . . . . . . . . . . . Section 5 Cable Specifications . . . . . . . . . . . . . . . . . . . . . Section 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 8 LED Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 5 6 7 8 9 10 11 3 Ethernet Card forPCI Section 1 Introduction Your Ethernet hub card is a high performance network device that is designed to easily link four 10/100Mbps hub with a 100Mbps PCI interface card. The hub card consists of four (4) 10/100BASE-TX hub port to linking and forwartding packets in one segment, it also includes a 32-bit PCI interface to provide an additional connection with the network segment. The Ethernet hub card is designed for plug-and-play installation and easy managements with all 10/100Mbps ports and LEDs on the bracket. Summary of features · Compliant with the 10BASE-T, 100BASE-TX specification of the IEEE 802. 3 standard · All 10/100Mbps hub port supports auto-negotia tion and ato-detection for 10 or 100Mbps · Equipped with four LEDs for easy viewing and troubleshooting · Equipped with a 100Mbps MAC interface to pro vides a connection with the 10/100Mbps hub seg ment · Diagnostic software and network drivers on the diskette · 32-bit bus mastering for high throughput and low processor utilization 4 Ethernet Card for PCI Section 2 Installation This section describes how to install your Ethernet hub card. Perform the following steps to install the adapter. Turn off your computer and all peripherals. Make a note of the cables and cords that are connected to the computer and disconnect them. Remove your personal computer's cover (refer to the owner's manual of your personal computer). Select any available PCI slot, and remove the slot cover. Carefully install the Ethernet hub card into the ex-pansion slot by firmly pressing the card into the edge of the connector slot until the card is snugly seated in the expansion slot and fasten the retaining bracket with screw from the slot cover. Reinstall your personal computer's cover and re-connect the power cord and all cables. [. . . ] · Cable for RJ-45 connector for 10Mbps network Cable type: twisted pairs 22, 24 or 26 AWG Category: Twists per foot: Nominal impedance: Maximum cable length: Maximum Attenuation: at UTP with 2 of 3, 4, or 5 2 to 3(min. ) 100 ohms 300'(100m) 8 to 10 dB per 100m 10Mz · Cable for RJ-45 connector for 100Mbps network Cable type: twisted pairs of AWG Category: Twists per foot: Nominal impedance: UTP with 2 26 5 2 to 3(min. ) 100 ohms 8 M20082217500 Ethernet Card for PCI Maximum cable length: 300'(100m) Section 6 Troubleshooting This section describes reasons for some adapter's f a i l u r e s and the actions to be taken to resolve the problems. · PCI scan specified, device not found Action: Verify that the PCI Ethernet adapter is physically installed properly. Otherwise, install the card in a different PCI slot or replace the adapter. [. . . ]