User manual TRENDNET TE100-H8E

[. . . ] Quick Installation Guide Note: Please read this Quick Installation Guide prior to installing the hub. PACKAGE CONTENTS Fast Ethernet 100Base-TX 5-port Mini Hub AC to DC (+12VDC 800mA) Power Adapter Mounting Hardware This Quick Installation Guide The Rear Panel Ethernet bandwidth If you want to connect more than 5 ports, you can use the hub's uplink port to connect to another 100Base-TX hub. In compliance with IEEE802. 3u Class II specification, two repeaters can be cascaded by using a 5 meter RJ45 cable in a single collision domain. The rear panel is equipped with DC power socket, 5 Shielded Twisted-Pair (STP) ports, and one Uplink slide switch. 1. [. . . ] 1 of second hub when Uplink switches are set to same mode. The Front Panel The front panel indicates LEDs status. The LED indicators will help you monitor the status of each port and connected segments. There are 5 LEDs on the front panel; Power (PWR), Collision (COL), Link/Activity, Error and Utilization. HARDWARE INSTALLATION Quick Installation Procedure 1. LED Function Color Power Collision Link/Activity Description Unlit: Power Off Amber Lit: Data collision occurs Green Lit: Indicates the adapter is connected to the hub Blinking: Data receiving Error Yellow Blinking: Data error occurs Lit: Indicates partition and isolation of port Utilization Green Indicates the hub's traffic of the Fast Uplink Multiple Hubs 4. Green Lit: Power On Place hub on a level and smooth surface. Connect power adapter to 120V AC power outlet. Connect the Adapter's DC jack to the hub's DC input. Connect workstations to hub using straight-through Category 5 UTP cabling. Connect one end of the cable (RJ-45 connector) to the port on hub and connect the other end to the RJ-45 port on the Fast Ethernet card in the workstation. The maximum cable distance between the hub and the workstation is 100 meters. Connect each device (up to 5) on your network using the same process in Step 3. Product Specifications Standard IEEE802. 3u, 100Base-TX Class II Repeater Number of 100Base-TX ports Uplink port Cable Distance Shared Port # 1 (Slide Switch) 5 Meters from hub to hub 100 Meters from hub to workstation Cabling Expandability LEDs UTP Category 5 8 ports on class II standard Power ­ Green Collision ­ Amber 5 Link/Activity ­ Green 5 Error ­ Yellow 4 Utilization ­ Green Power Adapter Temperature Humidity Dimensions Certification Copyright Notice Contents are subject to revision without prior notice. Trademarks All other trademarks belong to their respective owners. AC to DC (+12V 800mA) Operation 0 to 50¢J 5% to 95% non-condensing 5 FCC Compliance Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in residential installation. This equipment generated, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] CE Mark Declaration of Conformance TRENDware International, Inc. D-102 Torrance, CA 90501 Tel: 310-328-7795 Fax: 310-328-7798 www. trendware. com th TE100-H5E 100Base-TX 5-Port Mini Hub Quick Installation Guide 160 x 120 x 30 mm FCC Class A, CE, VCCI This is to certify that this product complies with ISO/IEC Guide 22 and EN45014. It conforms to the following specifications: EMC : EN55022(1988)/CISPR 22(1985) EN60555-2(1987) prEN55024-2(1990)/IE801-2(1991) prEN55024-3(1991)/IE801-3(1984) PrEN55024-4(1992)/IE801-4(1988) Class B Class A 4KV CD, 8KV AD 3V V/m 1KV - (power line) 0. 5KV - (signal line) This product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC. P/N : 7743901011 [. . . ]