User manual TRENDNET TE100-MFP1

[. . . ] TRENDnet User's Guide Cover Page TRENDnet User's Guide Table of Contents Change Admin Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Change User Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Contents Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Log into the management see "Access the management page" on page 11). Click on General tab and scroll down to the Language section 3. Enter the updated device information Click Apply. Select your desired language on the pull down menu. Click Apply to save settings. Change Admin Account Setting Administrator By default username and login password of the device is admin for both username and password. It is recommended to change the default password for added security. You can change both login username and password of the device management page by following the steps below. Note: Changes to these settings are case sensitive and should be written down somewhere and stored. Log into the management page see "Access the management page" on page 11). Click on Administrator tab and scroll down to the Set Administrator section UPnP General Universal Plug and Play (UPnP) is a networking protocol that makes your networking devices discoverable in the network. By default the UPnP setting is set to enable. The device can be discovered under your computer's network map 1. Log into the management page (see "Access the management page" on page 11). Click on General tab and scroll down to the UPnP section © Copyright 2011 TRENDnet. 7. TE100-MFP1 Under Permission section select the type of access you would like to permit user accounts with; Read Only or Read-Write. Click Add to create the new user account information. To delete a user account, select the user account you would like to delete. 3. 5. Under Administrator section enter your new username information. Under New Password and Re-Type Password section, enter your new password information. Click the Delete button to permanently remove selected user account. Change User Account Setting Administrator A user account does not have the ability to make changes to the device settings. You can assign a user account's password information by following the steps below. You can add a user account and assign both username and password for each user accounts by following the steps below. Note: Changes to these settings are case sensitive and should be written down somewhere and stored. [. . . ] TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. [. . . ]