User manual TRENDNET TE100-PCIFC

[. . . ] 17 VLAN SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Add/Remove VLAN Setting for add/remove VLAN VLAN01 (VLAN ID =1) added Driver setting changed by NIC Control Set Remove VLAN/Change VLAN property 18 18 18 19 20 DOS DIAGNOSTIC UTILITY 21 DIAG UTILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 MAIN MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 FUNCTIONS KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the autorun pop up, click Install Driver, and then click your operating system. <Note> If the autorun did not appear, please go to the disk driver, right click on the explorer. In the Driver folder, click the the driver of Windows 98SE_ME_2K_XP_Srv2003_Vista x86 Edition, then click WinSep. exe to execute the program. Step 11: Wait until the TE100-PCIFC finishes the installing. 8 Step 12: If the following screen pop up, insert the Windows 98SE CD-ROM into CD-ROM driver. (For Windows 98SE only) Step 13: Click OK to reboot your computer. 9 Connecting Remote Wake-Up Cable The unit support optional Wake-on-Lan magic packet feature. Proceed with the installation only when your PC supports this remote wake-up and you wish to use this function. If your PCI bus supports version 2. 2 or higher, there is no Wake-Up cable required. The feature can be enabled without using the cable. For more detail information, please check the User's Guide of your Motherboard. Wake-on-LAN magic packet Step 1: Step 2: Step 3: Step 4: Step 5: Make sure the power to the PC is off. Check if the TE100-PCIFC is properly installed in a PCI slot. Connect the cable from TE100-PCIFC to motherboard connector. Proceed to "Connecting to Your Network" Section. Connect Remote Wake-Up cable from TE100-PCIFC to motherboard connector. Plug in Remote Wake-Up cable to connector on Ethernet Adapter. 10 Connecting to Your Network Fiber Adapter This section describes how to connect the Fiber Adapter to a 100 Mbps fiberbased Ethernet network, which contributes to its optimal performance. <Note> You must connect the Fiber Adapter to the network before installing the network driver. Step 1: Step 2: Step 3: Remove the protective cover from the TE100-PCIFC fiber connector. Prepare a network cable with corresponding connectors for the two end devices, one end to the Fiber Adapter and the other to a 100Mbps fiber port on the network hub or switch. Connect the network cable to the connector on the Fiber Adapter. This network cable consists of two individual cables: one for `transmission (TX)', and the other for `reception (RX)'. Connect the other end of the network cable to a 100Base-FX hub or a switch. Step 4: <Note> i. Insert the cable that is connected to the transmit (TX) connector on the Fiber Adapter into the receive (RX) connector on the network hub or switch. Insert the cable that is connected to the receive (RX) connector on the Fiber Adapter into the transmit (TX) connector on the network hub or switch. Step 5: Step 6: When the cable is properly connected to two end devices, turn on the power to the PC. The LED will come on when the Fiber Adapter is receiving a good link signal from the connected device, a hub or switch. 11 Cabling Requirements For connector type, cabling requirements, and maximum segment distance when connecting the TE100-PCIFC to your network, please refer to the following table. Fiber Connections Type SC <Note> The maximum node-to-node network distance is in full-duplex operation. Wavelength of 1300nm Fiber Optic required Multi-mode, 62. 5/125 µm Max. Distance (* full-duplex) 2 km 12 NIC Control Set Utility The NIC Control Set is a Windows-based application. It provides Network Interface Card information, setting, statistics and diagnostic function. Also, it provides multiple VLAN function. My Computer NIC All NIC drivers are currently installed in this computer. Protocol All network protocols are currently installed in this computer. 13 Service All network services are currently installed in this computer. Client All network clients are currently installed in this computer. 14 General Display the basic information of the adapter, such as MAC Address, IP Address, Link Speed, and Duplex Mode. 15 Setting Display and set the parameters of the adapter by disable & enable the function. Statistics Display all the statistics information of the NIC. 16 Diagnostics Diagnose the hardware functionality: MAC Registers, PHY Registers, Loopback and Cable Link. The continuous option can be set as an infinite loop of testing. Please be award that perform this task will temporary disable the adapter. [. . . ] LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Some TRENDnet products include software code written by third party developers. [. . . ]