User manual TRENDNET TE100-PCIW

[. . . ] Test the adapter by running DIAG100. EXE diagnostic program. Select "Diagnose", then select "Diagnosis". If you have two TE100-PCIW cards in the network, after the cards passes the Diagnosis, you can run "PingPong", Set one computer as " Sender" and the other as "Receiver", the computers will send and receive packets back and forth. [. . . ] A:) At the NetWare prompt, run the INSTALL. NLM program by typing LOAD INSTALL <Enter> Choose the driver to start the driver to start the driver loading and binding procedure. This will allow you to load and bind the frame types supported by NetWare Add the LOAD and BIND statements required to the server is AUTOEXEC. NCF file so that the driver will be loaded automatically each time the server starts Diagnose the adapter There is a Diagnostic program in the diskette. To run this program, type in the following code at the DOS prompt: A:\DIAG100 The main menu has the following options: 1. Diagnose: adapter card's self-diagnosis Select: select the adapter (when there are multiple cards are installed) Help About Exit LED Function Color ACT LINK 100 Description Green Blinking: Data Transmitting Green Lit: Indicates that the link is established. Green Lit: Indicates the network is connected to 100Mbps port 1. In the Program Manager Main window, double-click on the Control Panel icon to install the driver. 4. 3. Insert the driver disk into drive A. Type the directory A:\WINNT into the box on your screen and press Enter key. FDX Green Lit: Card operates in Full duplex mode 4. 5. Select the PNIC-100 Fast Ethernet Adapter". Click on "Next", then install the network protocols and services that you want. See your Microsoft Windows NT user guide(s) for more information. HARDWARE INSTALLATION Quick Installation Guide 1. Install the Adapter in the Bus Master PCI slot of the computer. Connect the UTP cable to the Adapter and network hub. 6. NT will copy the necessary network drivers to your computer. Upon completion, you will see a list of installed bindings. You can change the bindings settings as necessary if needed. Product Specifications Standard IEEE802. 3/802. 3u 10BaseT/100Base-TX standards Bus Interface Hardware Interrupts Base I/O Address Cable Connections 32-bit bus master PCI INTA Assigned by BIOS RJ-45(10Base-T) UTP Category 3, 4, 5 or better. RJ-45(100Base-TX) UTP Category 5 or better Software Compatibility Microsoft Windows NT, Windows 95/98, LAN Manager, Novell Netware, Windows for Workgroups, IBM LAN Server, IBM LAN Support, NDIS Driver, DEC PATHWORKS, Banyan, IBM TCP/IP for DOS & OS/2, SCO UNIX, Packet Driver, FTP PC/TCP, NCSA TCP/IP LED Indications LINK ­ Green ACT ­ Green 100 ­ Green FDX ­ Green Input Power Requirements 100 - 240 VAC, 50 -60Hz Power Consumption 4. 2W Operational States (Full load) 3. 9W Static State Dimensions Certification Copyright Notice 130 x 70 mm FCC Class A, CE Mark Trademarks All other trademarks belong to their respective owners. FCC Compliance Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Shielded interface cables and AC power cord, must be used in order to comply with emission limits. CE Mark Declaration of Conformance This is to certify that this product complies with ISO/IEC Guide 22 and EN45014. It conforms to the following specifications: EMC EN55022(1988)/CISPR22(1985) EN60555-2(1987) prEN55024-2(1990)/IE801-2(1991) prEN55024-3(1991)/IE801-3(1984) PrEN55024-4(1992)/IE801-4(1988) Class A Class A 4KV CD, 8KV AD 3V V/m 1KV - (power line) 0. 5KV - (signal line) TE100-PCIW 10/100Base-TX PCI Bus Ethernet Adapter Quick Installation Guide TRENDware International, Inc. [. . . ]