User manual TRENDNET TE100-PCIWN

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. VCCI Class B Compliance (Japan) 2 Introduction Thank you for choosing the 32-bit PCI-Bus 10/100Mbps NWay ACPI Fast Ethernet Card, this card is auto-configurable upon power up and also supports auto-negotiation to automatically select the optimum speed and communication mode of an attached device. Additionally, the 32-bit PCI-Bus 10/100Mbps NWay ACPI Fast Ethernet Card complies with ACPI, and PC99, and includes support for Remote Wake-Up by Magic PacketTM, LinkChg and Microsoft®wake-up frame. [. . . ] Even if the PC is powered off network card is always active and monitoring the network. When a wake-up packet is detected, the card signals the motherboard to power up the PC. With the PC powered on, maintenance and other support tasks can be performed. 4 Product Featues Designed for versatility and performance, the 32-bit PCI bus 10/100Mbps Fast Ethernet Adapter provides the following features: · Compliant to IEEE 802. 3, 10BASE-T standard · Complaint to IEEE 802. 3u 100BASE-TX standard · Compliant to IEEE ANSI/802. 3 NWay Auto-negotiation standard · Compliant to PCI 2. 1, 2. 2 standards · Compliant to PC99 standard · Supports Wake-On-LAN function for remote wake-up (AMD Magic Packet, LinkChg and Microsoft wake-up frame) · Supports 4 Wake-On-LAN (WOL) signals (active high, active low, positive pulse, and negative pulse) · Supports ACPI, PCI power management. · Half/Full duplex capability · Supports Full Duplex Flow Control (IEEE 802. 3x) · Built-in FIFO buffers reduce overhead of memory transfers. · Drivers for all leading Network Operating Systems. · Two LED indicators: Link, Activity. · Link Indicator A steady green LED indicates good linkage between the 32-bit PCI bus 10/100Mbps Fast Ethernet Adapter and its supporting hub. · Activity Indicator A flashing green LED indicates that the adapter is sending or receiving data. 5 Installation Installation the 10/100Mbps PCI bus Fast Ethernet Card requires Hardware installation first, then BIOS and Software installation. 6. Switch off the computer, unplug the power cord, and remove the computer's cover. Select an unused PCI bus-master slot and remove its protective bracket. Carefully insert the card and press until all the edge connectors are firmly seated inside the slot. Then, screw the card's bracket securely into the PC's chassis. Attach the Wake-On-LAN cable (for installing TE100-PCIWA on PCI 2. 1 Motherboard only). If you require Wake-On-LAN capability, attach one end of the 3-pin Wake-On-LAN cable to the connector on the top edge of the card, and the other end to the "WOL" connector on the computer's motherboard. Refer to your computer's installation manual to locate this connector. Install the bracket screw, which secures the card to the cinouter chassis. Replace the computer's cover and connect the network cable to newly installed network card. Reconnect the computer's power cord and plug it into the power outlet. 6 Step 2, BIOS Configuration Due to a fault in some Plug-n-Play BIOS programs, it happens occasionally that a newly installed adapter is assigned an Interrupt Number which is already assigned to another device. [. . . ] Ascertain that the adapter's PCI slot is not deactivated at the BIOS level. The CMOS Setup utility in PCI computers ordinarily provides the option to activate or deactivate PCI slots. Replace the adapter in question with a verified adapter, reboot the computer to DOS by using a DOS diskette or a Window's Startup disk, and run RSET8139. EXE diagnostic tests on the sofrware diskette at directory of \DIAG\. Note:RSET8139. EXE was written for running in DOS environment. It may not run properly in the DOS prompt in Windows. 4. 5. Install the questioned adapter in another PCI computer and run the tests again. Remove all other PCI adapters from the computer and run the tests again. [. . . ]