User manual TRENDNET TE100-S24WS

[. . . ] 24-Port 10/100Mbps Fast Ethernet Web Smart Switch User's Guide FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. CE Mark Warning This is a Class A product. [. . . ] LED indicators of the Switch Power and System LEDs POWER: Power Indicator On Off : When the Power LED lights on, the Switch is receiving power. : When the Power turns off or the power cord has improper connection. SYSTEM: Management Indicator Blinking On/Off : When the CPU is working, the System LED is blinking. : The CPU is not working. Ports 1~24 Status LEDs Link/ACT: Link/Activity On Blinking Off : When the Link/ACT LED lights on, the respective port is successfully connected to an Ethernet network. : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the Ethernet network. : No link. 13 100Mbps On Off : When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. : When the respective port is connected to a 10Mbps Ethernet network, or no link. Fiber Module LEDs FX Link/ACT: Link/Activity On : When the fiber module is installed and connected to an Ethernet network, the FX Link/ACT LED lights on. Blinking : When the FX Link/ACT LED is blinking, the fiber module is transmitting or receiving data on an Ethernet network. Off : No link. FDX: Full Duplex On Off : When the FDX LED lights on, the fiber port is in full duplex mode. : When the green light is off, the fiber port is in half duplex mode. 14 CONFIGURATION Through the Web Browser you can configure the Switch such as VLAN, Port Setting, and System Setting . . . etc. With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware. Installing the Web Management Utility The following gives instructions guiding you through the installations of the Web Management utility. Insert the Utility CD in the CD-Rom Drive. From the Start menu on the Windows desktop, choose Run. In the Run dialog box, type D:\Web Management Utility\setup. exe (D:\ depends where your CD-Rom drive is located) and click OK. Follow the on-screen instructions to install the utility. Upon completion, go to Program Files -> web_management_utility and execute the Web Management utility. Web Management Utility The Web Management Utility was divided into four parts, Discovery List, Monitor List, Device Setting and Toolbar function, for details instruction, follow the below section. Discovery List This is the list where you can discover all the Web management devices in the entire network. By pressing the "Discovery" button, you can list all the Web Management devices in the discovery list. Double click or press the "Add to monitor list" button to select a device from the Discovery List to the Monitor List. 16 System word definitions in the Discovery List: l l l l l l l l l MAC Address: Shows the device MAC Address. IP Address: Shows the current IP address of the device. Protocol version: Shows the version of the Utility protocol. Product Name: Shows the device product name. System Name: Shows the appointed device system name. Location: Shows where the device is located. [. . . ] The Login Timeout is to set the idle time-out for security issue, when there is no action when running the Web Smart Utility and the time is up, you must re-login to Web Smart Utility before you set the Utility. Fill up the IP Address, Subnet Mask and Gateway for the device. Figure 22. System Setting 28 Trap Setting The Trap Setting enables the device to monitor the Trap through the Web Management Utility, set the Trap IP Address of the manager where the trap to be sent. Figure 23. Trap Setting u System Events: Monitoring the system's trap. [. . . ]