User manual TRENDNET TE100-S800I

[. . . ] Introduction The 8 10/100Base-TX Management Switch is a compact switch that is ideal for SOHO (Small Office or Home Office) networks. It provides wired-speeds, Fast Ethernet switching, and store-and-forward switching to attain high-performance at low-cost connections. It can also auto-learn and store source addresses on an 8K-entry MAC address table. The Switch provides 8 auto-sensing 10/100 Mbps RJ-45 Ethernet ports, supporting Auto-MDIX function for each port. [In general, MDI means connecting to another Hub or Switch while MDIX means connecting to a workstation or PC. [. . . ] If no trap manager is defined, no traps are issued. Create a trap manager by entering the IP address of the station and a community string. Actions-> <Add>: Create a trap manager. Finished configure press ESC to go back action menu line. After delete item press <Save> to complete the deleting operation. <Quit>: Exit this page and return to previous menu. 4-4-3. GVRP This page you can enable / disable the GVRP (GARP VLAN Registration Protocol) support. Press Space key to choose Enabled / Disabled. Actions-> <Edit>: Configure all items. Press Space key to choose Enable or Disabled mode. Finished configure press ESC to go back action menu line. <Quit>: Exit this page and return to previous menu. 44 4-4-4. LACP 4-4-4-1. Aggregator Setting 1. Group: Display the trunk group ID. 2. LACP: Press Space key to enable or disable LACP (Link Aggregation Control Protocol) support. If enable, the group is LACP static trunking group. If disable, the group is local static trunking group. 3. LACP Work Port Num: The max number of ports can be aggregated at the same time. If LACP static trunking group, the exceed ports is standby and able to aggregate if work ports fail. If local static trunking group, the number must be the same as group ports. NOTE: Before set LACP support, you have to set trunk group on the page of Port / Trunk Configuration first. Actions-> <Edit>: Configure all items. Finished configure press ESC to go back action menu line. <Quit>: Exit this page and return to previous menu. 4-4-4-2. State Activity Active: The port automatically sends LACP protocol packets. Passive: The port does not automatically sends LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device. 46 Actions-> <Edit>: Configure all items. Finished configure press ESC to go back action menu line. <Quit>: Exit this page and return to previous menu. 4-4-4-3. LACP Status When you setting trunking group, you can see relation information in here. Actions-> <Quit>: Exit this page and return to previous menu. <Previous Page>: Return to previous page to view. [. . . ] You can save current EEPROM value from here, then go to the TFTP restore configuration page to restore the EEPROM value. 80 5-4-14. Reset System Reset Switch to default configuration, default value as below 5-4-15. Reboot Reboot the Switch in software reset. 6. Technical Specifications This section provides the specifications of the 8 10/100Base-TX Management Switch and the following table lists the specifications. IEEE802. 3, 802. 3u IEEE802. 3x Flow control and Back pressure Standards Compliance IEEE802. 1D Spanning Tree protocol IEEE802. 1Q VLAN Tagging IEEE802. 1p Class of Service IEEE802. 3ad Link aggregation Protocol CSMA/CD 14880 packets per second for 10Mbps 148800 packets per second for 100Mbps Per unit: Power LED Indicators Per RJ-45 port: Link/Activity, 100Mbps, Full duplex/Collision Network Cables MAC Address Data Buffer Switch Fabric Bandwidth Transfer Rate UTP/STP Cable: 100Meters 8K MAC address Table 2Mbits Non-blocking store-and-Forward, Up to 3. 8Gbps 250mm x 133mm x 37mm (L x W x H) 1082gw -40 to 70 , Non condensing 0 ~ 45 82 Dimensions Weight Storage Temp. [. . . ]