User manual TRENDNET TE100-S81FX

[. . . ] 4 PRODUCT FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PACKING LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Uplink Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] User's Manual 3 8-port Ethernet Switch This compact switch has seven RJ-45 ports and one fiber port. Each of the RJ-45 port is capable of auto-negotiate 10/100Mbps and full or half-duplex mode. The multimode fiber port is able to accommodate SC connector. The switch combines fiber and TX ports in a compact box, providing an inexpensive solution for interconnecting between buildings in a campus, multitenant location covering large areas or industrial environment. The fiber port provides the long distance capability and the space saving compact size makes it ideal for wall mounting or desktop. Store-and-forward, true non-blocking architecture and auto-negotiation are features of this switch to optimize performance and value of this switch. Installation and operation involves simply plugging in cabling and connecting power. This 8-port switch represents affordable, reliable, and easy-to-use LAN solutions. 4 User's Manual Product Features List of features includes: · · · · · · · · · · · Fiber-optic connection for SC TX ports with auto-negotiation 10/100Mbps Auto-negotiation for speed and duplexity True non-blocking architecture Store-and-forward mechanism Back pressure and IEEE 802. 3x compliant flow control Supports 1K MAC addresses One uplink port Rear DIP switch to force fiber transmission to half duplex Front panel port utilization and status LEDs Wall-mountable compact size Packing List When you unpack the switch, you should find the items listed below. Report any apparent damage or missing items immediately to your authorized reseller. · · · The 8-Port Switch User's manual AC power cord User's Manual 5 Front Panel The following pages explain the front LED functions. Figure 1: Front Panel Power: Indicates that there is power to the switch. 100/TX: Indicates the presence of 100Mbps when steady and flashes upon transmission (TX) 6 User's Manual 10/RX: Indicates the presence of 10Mbps when steady and flashes when receiving (RX) data FDX/COL: Detects the presence of full-duplex (FDX) and flashes upon collision (COL) of traffic Uplink Port An uplink port allows connection, through the TX ports, to another regular (i. e. The labeled uplink port on the switch is located adjacent to port 7TX. Port 7TX & uplink-port are mutually exclusive. If port 7TX is in use, the uplink-port will be automatically disabled and vise versa. If connecting to an uplink port of a hub or another switch, any of the regular ports can be used. To connect two regular RJ-45 ports between any two switches or hubs, you need a cross-wire cable. DIP Switch The DIP switch allows fixed settings. Locate the DIP switch in the back of the switch. Pin 1: changes the traffic of the fiber-optic port to halfduplex when moved up to the ON position; full-duplex in the OFF position. User's Manual 7 Pin 2: enables fixed-setting of the TX Port 1 by moving up to the ON position; activates auto-negotiation in the OFF setting. Pin 2 must be in the ON position in order to change port settings with pins 3 and 4. Pin 3: forces 10Mbps speed on port 1 when in the ON position; forces 100Mbps speed on port 1 when in the OFF position. Note: new setting will not be activated unless fixed-setting is enabled. [. . . ] Multiple, widely dispersed LAN systems are referred to as a wide area network (WAN). Ethernet Technologies More than 80 percent of all LANs utilize Ethernet technology. The Institute of Electrical and Electronic Engineers (IEEE) standardized Ethernet in IEEE 802. 3, which provides for configuration rules, interaction requirements, types of media, and data rate. 16 User's Manual Fast Ethernet For networks that need higher transmission speeds, a faster speed was developed and IEEE next established IEEE 802. 3u, raising the Ethernet speed from 10Mbps to 100Mbps. Thus, fast Ethernet arose and users quickly began converting from 10Mbps to 100Mbps. Gigabit Ethernet The demand for even higher speed created the gigabit Ethernet at 1000Mbps (or 1Gbps). [. . . ]