User manual TRENDNET TEG-224WSPLUS

[. . . ] FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. UL Warning a) Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. [. . . ] Supported input voltages range from 100-240V AC at 50-60Hz. Reset: The Reset button is to reset all the setting back to the factory default. Note: Be sure that you recorded the setting of your device, else all the setting will be erased when pressing the "Reset" button. 13 14 UNDERSTANDING LED INDICATORS The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed. Ports 1~24 10/100M Status LEDs Link/ACT: Link/Activity On : When the Link/ACT LED lights on, the respective port is successfully connected to an Ethernet network. : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the Ethernet network. LED indicators of the Switch 100Mbps Power and System LEDs POWER: Power Indicator On Off : When the Power LED lights on, the Switch is receiving power. : When the Power turns off or the power cord has improper connection. On : When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. : When the respective port is connected to a 10Mbps Ethernet network Off Ports 25~26 Gigabit Status LEDs mini-GBIC On Off : When the mini-GBIC module is installed, LED will lights on : No mini-GBIC module is installed SYSTEM: Management Indicator Blinking On/Off : When the CPU is working, the System LED is blinking. : The CPU is not working. Link/ACT: Link/Activity On : When the Link/ACT LED lights on, the respective port is successfully connected to an Ethernet network. : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the Ethernet network. : No link. Blinking Off 15 16 1000Mbps On : When the 1000Mbps LED lights on, the respective port is connected to a 1000Mbps Gigabit Ethernet network. : When the respective port is connected to a 10Mbps Ethernet or 100Mbps Fast Ethernet network CONFIGURATION Through the Web Browser you can configure the Switch such as VLAN, Trunking, QoS. . . With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware. Off 100Mbps On : When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. : When the respective port is connected to a 10Mbps Ethernet or 1000Mbps Gigabit Ethernet network. Installing the Web Management Utility 1. Insert the Utility CD in the CD-Rom Drive. TRENDnet's Autorun screen will appear. Click Install Utility to install the Web Management Utility onto your PC. Off 2. 3. Follow the on-screen instructions to install the utility. Upon completion, go to Program Files -> web_management_utility and execute the Web Management utility. (Figure 6) 17 18 System word definitions in the Discovery List: MAC Address: Shows the device MAC Address. IP Address: Shows the current IP address of the device. Protocol version: Shows the version of the Utility protocol. Product Name: Shows the device product name. [. . . ] Be aware that the entire configuration will be reset, the IP address of the device will be set to default setting 192. 168. 0. 1. Figure 30. Set Password Logout When press this function, the web configuration will go back to first Login page. Backup Setting The backup tools help you to backup the current setting of the Switch. Once you need to backup the setting, press the "Backup" button to save the setting. To restore a current setting file to the device, you must specify the backup file and press "Restore" button to proceed the setting of the recorded file. Figure 31. [. . . ]