User manual TRENDNET TEG-240WS

[. . . ] FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. CE Mark Warning This is a Class A product. [. . . ] System Information Setup Setting Find that there are seven items, including Port Setting, IEEE 802. 1Q VLAN Settings, Trunk Setting, Mirror Setting, IEEE 802. 1p Default Priority, Broadcast Strom Control Setting, Jumbo Frame Setting in 27 Setup menu. Port Settings In Port Settings menu (Figure 17), this page will show each port's status, selected drop down menu to set each port's Speed, and QoS priority then press "Apply" button to activate changes. To refresh the information table to view the latest port setting and Link Status, press the Refresh button. The Link Status in the screen will show the connection speed and duplex mode; else this dialog box will show Down when the port is disconnected. Figure 17. Port Setting Note: The priority of Gigabit Fiber port is higher than Copper. Speed: The 1000BASE-T connections can operate in Forced Mode settings (1000M Full, 100M Full, 100M Half, 10M Full, 10M Half), Auto, or Disable. The default setting for all ports are Auto. The mini-GBIC (Gigabit Fiber) connections can operate in Forced Mode settings (1000M Full), Auto, or Disable 28 Flow Control: This setting determines whether or not the Switch will be handling flow control. Set Flow Control to Enable for avoiding data transfer overflow. Or it sets to Disable; there is either no flow control or other hardware/software management. When the port is set to forced mode, then the flow control will automatically set to Disable. QoS: Displays each port's 802. 1p QoS priority level for received data packet handling. Default setting for all ports is Middle. You can change the priority settings in 802. 1p Default Priority. IEEE 802. 1Q VLAN A VLAN is a group of ports that can be anywhere in the network, but communicate as though they were in the same area. VLANs can be easily organized to reflect department groups (such as R&D, Marketing), usage groups (such as e-mail), or multicast groups (multimedia applications such as video conferencing), and therefore help to simplify network management by allowing users to move devices to a new VLAN without having to change any physical connections. The IEEE 802. 1Q VLAN Configuration page provides powerful VID management functions. The original settings have the VID as 01, named "default", and all 24 ports as "Untagged". Asymmetric VLAN IEEE 802. 1Q Asymmetric VLAN default setting is "Disabled", you can press "Enabled" radio button and Apply it to submit the 29 Asymmetric VLAN function. Figure 18. Enabled Asymmetric VLAN function Figure 19. Change setting warning message Note: The Settings of VLAN, IGMP Snooping and Forwarding Table will be reset to default. Untag Asymmetric VLAN Setting: The IEEE 802. 1Q VLAN Configuration page provides powerful VID management functions. The original default VLAN setting has the VID as 01, named "default", and contains all ports as "Untagged". 30 Figure 20. 802. 1Q Asymmetric VLAN Setting Add VID: Click to create a new VID group, assigning ports 1 ~ 24 as Untag, Tag, or Not Member. [. . . ] Please contact the pointofpurchase for their return policies. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not 65 remove or attempt to service the product by any unauthorized service center. [. . . ]