User manual TRENDNET TEG-424WS

[. . . ] FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. CE Mark Warning This is a Class A product. [. . . ] Monitor Load: To manually load the setting file of the Monitor List. Exit: To exit the Web Management Utility. In the "View TAB", there are view log and clear log function, this function will help you to show trap setting. View Log: To show the event of the Web Management Utility and the device. In the "Option TAB", there are Refresh Time function, this function helps you to refresh the time of monitoring the device. Choose 15 secs, 30 secs, 1 min, 2 min and 5 min to select the time of monitoring. In the "Help TAB", there is About function, it will show the version of the Web Management Utility. 30 Configuring the Switch The TEG-424WS Gigabit Web Smart Switch has a Web GUI interface for smart switch configuration. The Switch can be configured through the Web Browser. A network administrator can manage, control and monitor the switch from the local LAN. This section indicates how to configure the Switch to enable its smart functions Login Before you configure this device, note that when the Web Smart Switch is configured through an Ethernet connection, make sure the manager PC must be set on same the IP network. For example, when the default network address of the default IP address of the Web Smart Switch is 192. 168. 0. 1, then the manager PC should be set at 192. 168. 0. x (where x is a number between 2 and 253), and the default subnet mask is 255. 255. 255. 0. Open Internet Explorer 5. 0 or above Web browser. Enter IP address http://192. 168. 0. 1 (the factory-default IP address setting) to the address location. Figure 13. Or through the Web Management Utility, you do not need to remember the IP Address, select the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser. When the following dialog page appears, remain enter the default password "admin" and press Login to enter the main configuration window. 31 Figure 14. After entering the password, the main page comes up, the screen will display the device status. Figure 15 System Information 32 Setup Setting Find that there are seven items, including Port Setting, IEEE 802. 1Q VLAN Settings, Trunk Setting, Mirror Setting, IEEE 802. 1p Default Priority, Broadcast Strom Control Setting in Setup menu. Port Settings In Port Settings menu (Figure 16), this page will show each port's status, selected drop down menu to set each port's Speed, and QoS priority then press "Apply" button to activate changes. To refresh the information table to view the latest port setting and Link Status, press the Refresh button. The Link Status in the screen will show the connection speed and duplex mode; this dialog box will show Down when the port is disconnected. Figure 16. Port Setting Note: The priority of Gigabit Fiber port is higher than Copper. 33 Speed: The 1~24 100BASE-TX port connections can operate in Forced Mode settings (100M Full, 100M Half, 10M Full, 10M Half), Auto, or Disable. The default setting for all ports are Auto. The 25~28 1000BASE-T port connections can operate in Forced Mode settings (1000M Full, 100M Full, 100M Half, 10M Full, 10M Half), Auto, or Disable. The default setting for all ports are Auto. The 25~26 Mini-GBIC (Gigabit Fiber) connections can operate in Forced Mode settings (1000M Full), Auto, or Disable QoS: Displays each port's 802. 1p QoS priority level for received data packet handling. [. . . ] To restore a current setting file to the device, you must specify the backup file and press "Restore" button to proceed the setting of the recorded file. Figure 19. Backup Setting Note: when restoring a recorded file, the current password will not be erased. 69 Firmware Upload The Firmware Upload page helps you backup or upload firmware from/to the Switch. Once you need to backup the current firmware of the Switch, press the "Backup" button to save the current firmware of the Switch; To restore or upgrade firmware to the Switch, you must specify the firmware file and press "Upload" button to proceed the firmware upload. Figure 20. Firmware Upload System Reboot Provides a safe way to reboot the system and ensures the configuration has been saved, or all the changes you just made may be lost after system reboot. Figure 21. [. . . ]