User manual TRENDNET TEG-ECTX

[. . . ] The TEG-ECTX/TEG-ECSX is a high performance network adapter that supports advanced management and power savings functionality for system administrators. The TEG-ECSX has SC type port allow you connects Multi-Mode fiber devices at distances of up to 550m (1804ft. ) Full-Duplex technology generates data rates of up to 2Gbps over a motherboard's high-speed PCI Express Bus architecture. Jumbo Frame support further optimizes throughput performance. [. . . ] Step 2: When the cable is properly connected to the devices, turn the power on. The LED will be blinking when the PCI Express Gigabit Ethernet Adapter is receiving a good link signal from the connected device For TEG-ECSX Step 1: Connect a SC-type multi-mode cable from the TEG-ECSX to a Gigabit fiber converter. Step 2: Connect an Ethernet cable from the fiber converter to a Gigabit Ethernet port on your Gigabit switch. Step 3: When the cable is properly connected to the devices, turn the power on. The LED will be blinking when the PCI Express Gigabit Ethernet Adapter is receiving a good link signal from the connected device Note: Make sure the TX and RX cables are reversed on the opposing connection. -8- Cabling Requirement For connector type, cabling requirements, and maximum segment distance as list below. Speed Media Port Speed Half/Full Duplex 10/20 Mbps 100/200 Mbps 2000 Mbps Cable Distan ce 10BaseT RJ-45 UTP/STP Cat 3, 4, or 5 UTP/STP Cat 5 UTP/STP Cat 5e, 6 100M 100BaseTX 1000BaseT RJ-45 RJ-45 100M 100 M Fiber Type SC Wavelength of 850nm Fiber Optic required 62/125 µm (Multi-Mode) 50/125 µm (multi_mode) Maximum Distance (* full-duplex) 550 m 220 m <Note> The maximum node-to-node network distance is in full-duplex operation. -9- Diagnostics Utility The diagnostics utility is a Windows platform application. It provides general information, VLAN ID setting, Driver property settings, Diagnostics functions, Statistics, Cable analysis, and Wake on LAN function. Diagnostics Utility Installation Step 1: Insert the Driver CD-ROM into your computer's CD-ROM Driver Step 2: Click Diagnostics Utility button on the CD-ROM, choose the utility which suitable for your operation system. Step 3: Click Next Step 4: Click Next to continue or click Browse to choose an alternate location. -10- Step 5: Click Finish to exit the installation. Step 6: Click Start Diagnostics Utility. Program Realtek Diagnostics to launch the -11- Diagnostics Utility Configuration General This page shows the general information of the selected network adapter. VLAN This page shows information about VLANs on current the selected network adapter. User can add, remove or change the VLAN ID here. -12- Driver This page shows driver information of the selected network adapter. Advanced Setting This page displays working parameters of the network adapter. For Windows 98SE and ME, please reboot the computer to take the changes effected. -13- Diagnostics This page performs hardware tests of the selected network adapter. Send and Receive Two computers with its own adapter in the same LAN can perform send & receive experiment with broadcast packet here. -14- Statistics This page shows statistics of the current selected network adapter, including throughput, number of good packets have been sent and received, and number of error packets have been sent and received. Cable This page shows the connected cable length and status. -15- Wake On LAN (for TEG-ECTX only) This page shows three ways to wake up a computer in suspends or sleep mode. 1) Ethernet Address 2) IP Address 3) NetBIOS Name. A computer can be waked up only if related configurations in BIOS and the network adapter are enabled. -16- Specifications Standards 10/100/1000BaseTX: IEEE802. 3 10BaseT IEEE802. 3u 100BaseTX IEEE802. 3ab 1000BaseT 1000BaseSX/LX: IEEE802. 3z 1000BaseSX/LX 10Base T: 10/20Mbps (half/full Duplex) 100Base TX: 100/200Mbps(half/full-duplex) 1000Base T: 2000Mbps (full-duplex) 1000BaseSX: 2000Mbps (full-duplex) 14, 880pps for 10Mbps 148, 810pps for 100Mbps 1, 488, 100pps for 1000Mbps 10BaseT: UPT/STP Cat 3, 4, or 5 100BaseTX: UTP/STP Cat. 5e, 6 Fiber: 62/125µm multi-mode fiber-optic cable, up to 550 m, wavelength 850nm 50/125µm multi-mode fiber-optic cable, up to 220 m, wavelength 850nm LNK (Link) (Green) ACT (Activity) (Yellow) 137x 120 x 22 mm (5. 40x 4. 73 x 0. 87 inches. 3. 3VDC, 727mA, 2. 4W Max. Speed Performance Cable LEDs Dimensions Net Weight Power Consumption Temperature Operation Storage Humidity Emissions 0°C to 45° C (32°F to 113°F) -10°C to 70°C (14°F to 158°F) 10%-95% non-condensing FCC part 15 Class B, CE Mark Class B -17- Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEG-ECTX/TEG-ECSX­ 5 Years Warranty If a product does not operate as warranted above during the applicable warranty period, TRENDnet shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product. All products that are replaced will become the property of TRENDnet. [. . . ] TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, -18- UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. [. . . ]