User manual TRENDNET TEG-PCBUSR

[. . . ] Holding the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card with the LED indicator facing up then insert to the 32-bit PC Card slot. Slide the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card all the way into the 32-bit PC Card slot until it reaches a firm stop. Card Removal Use the computer's PC Card Eject mechanism to unseat the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card from the computer's PC Card slot. The PC Card will then protrude from the PC Card slot and you can easily remove the PC Card by gripping its protruding end and withdrawing it from the PC Card receptacle. 3 4 Driver Installation Before you connect the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card to the network, you have to install the network driver first. [. . . ] To configure this setting, select Disable or Enable from the drop-down menu, and click Modify button to confirm. Flow Control This section displays working parameters for this network adapter. For Windows 98SE and ME, it needs to reboot to change the parameters. Modify: Select the working parameter setting which you want to modify, then click Modify button to change the working parameter setting. The Flow Control allows user to minimize possible data loss during transmission on the network. To configure this setting, select Disable or Enable from the drop-down menu, and click Modify button to confirm. 802. 1Q/1p VLAN Tagging 9 10 Jumbo Frame choose Auto Negotiation to enable the device to automatically select the best transmission speed. This network adapter supports link speed ranging from 10Mbps to 1000Mbps and both full-duplex and half-duplex modes. Network Address The Jumbo Frame allows user to set the transmit packet data size. To adjust the value, select a data size from the drop-down menu. Sizes are available from 2KB MTU to 7KB MTU. Select Disable if you want to disable the setting. Link Speed/ Duplex Mode The Network Address allows user to change the physical address of your adapter. To set up a physical address, type any new address in the value field and click Modify button to save your MAC address. This figure displays a modified network address "1A2B3C4D5E6F". To power off the network adapter, select Not Present and click Modify button to confirm. The Link Speed/ Duplex Mode allow user to optimize the connection speed for data transmission. To configure this setting, select a combination of link speed and duplex mode from the drop-down menu, or 11 12 Offload Checksum the drop-down menu, and click Modify button to confirm. Wake-On-Lan After Shutdown The Offload Checksum allows user to decrease CPU utilization by offloading the task of CPU to the network adapter. To configure this setting, select a value from the drop-down menu and click Modify button to confirm. [. . . ] Otherwise choose "NetBIOS Name" and key in the NetBIOS Name (e. g. key in NetBIOS Name: PC1). Protocol Data Transfer Rate CSMA/CD Ethernet: 10Mbps (half-duplex) 20Mbps(full-duplex) Fast Ethernet: 100Mbps (half-duplex) 200Mbps (full-duplex) Gigabit Ethernet: 2000Mbps (full-duplex) Network Cables 10BASE-T: 2-Pair UTP/STP Cat. 5e, 6 Physical and Environmental Temperature Humidity EMI: Operating: 0° ~ 40° C, Storage: -10° ~ 70° C Operating: 10% ~ 90%, Storage: 5% ~ 90% FCC Class B, CE Mark B, VCCI-B 17 18 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEG-PCBUSR ­ 5 Years Warranty If a product does not operate as warranted above during the applicable warranty period, TRENDnet shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product. [. . . ]