User manual TRENDNET TEG-PCISX

[. . . ] 5 VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PRODUCT FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The IEEE 802. 1Q standard describes a methodology by which packets of data going through networking devices can be inserted with, or stripped of, VLAN identification information. VLANs can increase the efficiency, reliability and provide extra security for your network. Product Features Designed for versatility and performance, the adapter provides the following features: · Fully compliant with IEEE 802. 3z 1000BASE-SX Gigabit Ethernet standards and IEEE 802. 3 Ethernet standards. Maximum 1Gbps (1000Mbps) transmit and 1Gbps receive for a total of 2Gbps data throughput. PCI v2. 2 compliant. · · · · 6 · Operates in a 32- or 64-bit, 33/66 MHz PCI Bus slot. A 32-bit PCI Bus at 33Mhz supports 1Gbps throughput, a 64-bit PCI Bus at 33Mhz supports 2Gbps. PCI Bus Master greatly reduces the load on the CPU, freeing it for other tasks. Supports IEEE 802. 1Q VLAN specifications, with memory for up to 16 VLANs. Multi-mode SC Optical Fiber connector for network cable connection. Cable lengths up to 220 meters using 850nm 62. 5/125 fiber optic cable. Cable lengths up to 500 meters using 850nm 50/125 fiber optic cable. · · · · Built-in 96K buffers reduce memory transfer overhead and optimize operating bandwidth, throughput, and network data integrity. Level-One LXT1001GMAC (Gigabit Ethernet MAC) controller containing a built-in 64 bit, 33 MHz PCI interface. Four LED indicators: Link, 1000M, FDX (Full Duplex) and Tx/Rx (Transmit / Receive). Driver support for: Windows 95 (NDIS3) Windows NT 4. 0 (NDIS4) Linux OS Kernel v2. 0/2. 2 Windows 98 (NDIS5) Windows NT 2000 (NDIS5) Netware v4. 11/4. 2/5. 0 · · · 7 Installation Unpacking CAUTION: Under ordinary circumstances, a 1000Mbps Gigabit Ethernet Card will not be affected by static charge as may be received through your body during handling of the unit. However, there are special circumstances where you may carry an extraordinarily high static charge, and possibly damage the card and/or your computer. It is good practice to eliminate all static electricity by touching a ground (an unpainted metal area of your computer chassis, for example) before performing any installations. Open the shipping carton and carefully remove all items. In addition to this User's Guide, ascertain that you have: · · One 1000Mbps Gigabit Ethernet Card Card. One Software Driver diskette Installing the Adapter 1. Shut down the computer, unplug its power cord, and remove the chassis cover. Insert the contact edge of the 1000Mbps Gigabit Ethernet Card into the connector of any available PCI Bus Master expansion slot. Press the card firmly into the connector such that the card's contacts are fully seated in the connector. Install the bracket screw, which secures the card to the computer chassis. 8 4. Replace the computer's chassis cover. [. . . ] The valid range for the TXDMATHRESHOLD is 0 - 1514. DISABLERXIP ­ Disables the JT1ODI TCP/IP Receive Packet checksum support. By default, the JT1ODI will perform TCP/IP checksum verification on received packets in hardware if the operating system supports this capability. Due to the large number of Network Operating Systems (NOSs) supported, detailed driver software installation instructions are given in README. TXT files on the 1000Mbps Gigabit Ethernet Card Software Diskette. 14 Review the root directory README for overview information. [. . . ]