User manual TRENDNET TEG-S4000I

[. . . ] TEG-S4000i 4-Slot SNMP Modular Switch Ethernet / Fast Ethernet / Gigabit Ethernet User's Guide Version 2. 0 23-April-2003 1 Release Note 4 slot modular switch manual Update Version Progress status Remark QA PM 23/04/2003 V2. 0 On checking 1. Gigabit module (48360) MAC:4K, Buffer 128 Kbytes Richard 2 Table of Content Introduction Product Overview Network Configuration Connecting to the Network Web-Based Management SNMP Management Product Specifications Appendix A. Internet Explorer Setting Appendix B. VLAN Setting 3 1. Introduction Welcome to the World of Switching-Network. In modern business society, communication and information sharing are fundamental to our lifestyle. [. . . ] You may have to press Enter again when the switch is finished resetting. Port Setting This function is for port speed setup. For example, type "1" and "2" 2 of modular 1. More function to choice after typing 1, or 2 b. Pick any number you need to set up, for example, the option 2 is for the Full or Half mood setting. 27 Address table User can view the node's MAC address table of system, per module or per port, that attached on the device. Spanning Tree Protocol Spanning tree is a link management protocol that provides path redundancy while preventing undesirable loops in the network. 28 Broadcast Storm Filter IGMP Internet Group Multicasting Protocol (IGMP) is used to support real-time applications such as video conferencing or streaming audio. 29 VLAN Mode (2 modes) VLAN For Cpu(2 VLANs) 30 Secure IP for Telnet and HTTP The IP security is for Telnet and HTTP , if device is installed in a internet environment , switch may be attach by Hacker, then the system maybe will crash, for prevent this status, you can enable the function and setting the IP address, it provides four IP address, only authorized IP address can manage device. 31 5. Web-Based Management This section introduces the configuration and functions of the Web-Based management. About Web-based Management Inside the CPU board of the Modular Switch exists an embedded HTML web site residing in flash memory. It offers advanced management features and allow users to manage the Switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. The Web-Based Management supports Internet Explorer 5. 0 and later versions. It is based on Java Applets with an aim to reduce network bandwidth consumption, enhance access speed and present an easy viewing screen. Note: By default, IE4. 0 does not allow Java Applets to open sockets. The user has to explicitly modify the browser setting to enable Java Applets to use network ports. ( See Appendix A: for the means to modify the setting ) And you don't need to change any configuration if you use Netscape browser. System Login 1. Type http:// and the IP address of the Modular Switch ( for example, the default is 192. 168. 16. 1 ) in the Location or Address field. Press Enter. 32 Figure 5-1: The Password Window 3. The default is " root " for both. Press "Enter" or Click "OK", then the Home Screen of the Web-based management appear. System Configuration Figure 5-2 The Home Page Screen 33 Home The Home page displays the configuration of the Modular Switch. System Name : An administratively-assigned name of the managed unit, can be modified in SNMP page. System Location : The physical location of this managed unit ( e. g. , laboratory, 3rd floor ), can be modified in SNMP page. System Contact : The contact person for this managed unit, can be modified in SNMP page. System Up Time : The time last since the managed unit was reinitialized, read only. IP Address : The IP address of the managed unit, can be modified in IP Config page. Subnet Mask : The subnet mask of the managed unit, can be modified in IP Config page. Default Gateway : The default gateway of the managed unit, can be modified in IP Config page. [. . . ] We use Internet Explorer 5. 0 as demonstrational sample: We first select "Internet Optional. . " under "Tools" of function bar, then follow the step-by-step execution. Step 1: then select " Security " Step 2: select " trusted sites " 61 Step 3 : click " sites " Step 4 : add the IP of the Modular Switch to the zone, click " Add " Step 5: Disable left-bottom box ­ Require server verification for all sites in this zone, then click "OK" 62 Step 6: go back to Internet Options, then click " Customer Level " Step 7: pull down rolling to find "Java " Step 8: select " Custom " under "Java " 63 Step 9:select"Java Custom Setting" Step 10: select "Edit Permissions" Step 11: select "Enable" under "Unsigned Content", 64 Appendix B. VLAN Setting In Appendix B, We provide two examples of VLAN management on VLAN Group Configuration. The two examples will show you how to Configure VLAN Group: Port-Based VLAN The following example shows you how to create 2 Port-based VLANs including two overlapping ports. 65 Before you begin to create new VLAN Group, you need to set PVID number on Ports page as below: We set VLAN ID of Ports (1~4 ) 1, and PVID of Ports ( 5~8 ) 2. [. . . ]