User manual TRENDNET TEW-2K1 DATA SHEETS

[. . . ] AP Manager Installation Install the AP Manager to your PC 10 10 4. Configuring the AP with the AP Manager Startup and Login The General Setup Tab The AP Setup Tab The DHCP Client Tab The DHCP Server Tab 14 14 18 19 21 22 5. Product Specifications Specifications LAN Port Connector Specifications 24 26 29 29 31 3 11Mbps Wireless LNA Access Point User's Manual 1. Introduction Congratulations on your purchase of this 11Mbps Wireless LAN Access Point. This product is designed specifically for your 11Mbps wireless LAN environment needs. [. . . ] The AP Manager starts up. 14 11Mbps Wireless LNA Access Point User's Manual 4. Click the Search button to find Access Point. . 5. The computer starts searching for the Access Point. 15 11Mbps Wireless LNA Access Point User's Manual 6. Double-click on the searched Access Point. 7. Key in your User Name (default is "root") and Password (default no password) and then click OK button to continue. 16 11Mbps Wireless LNA Access Point User's Manual 8. The General Setup screen of AP Manager will be shown. 17 11Mbps Wireless LNA Access Point User's Manual The General Setup Tab The General Setup tab will display the AP name, and enable you change the AP name and password. If AP name or password had been changed, you need to click Save button to store new settings. Reset AP The function of this button is same as the hardware RESET Button on the front panel of Access Point. Click this button will re-boot Access Point. Restore Default Click this button to restore the Access Point default settings. Any setting you may have made through the AP Manager will be lost if this button is clicked. Download This button is used for firmware upgrade capability. If you click the download button to upgrade firmware, the Access Point will reboot automatically after download process. 18 11Mbps Wireless LNA Access Point User's Manual The AP Setup Tab The AP Setup tab allow you to set the wireless configuration items and WEP encryption. If any item had been changed, you need to click Save button to store new settings and then click Reset AP button on General Setup tab to make new settings effect. AP SSID SSID is used to identify the wireless LAN. The default primary DNS server is 10. 0. 0. 2 22 11Mbps Wireless LNA Access Point User's Manual Secondary DNS Server Secondary DNS Server address. The default Secondary DNS server is 10. 0. 0. 3 IP Address Range Whenever there is a request, the DHCP server will automatically allocate an unused IP address from the IP address Range to the requesting computer. You must specify the starting and ending address of the IP address Range. The default IP address range is from 10. 0. 0. 1 to 10. 0. 0. 253 23 11Mbps Wireless LNA Access Point User's Manual 5. FAQ & Troubleshooting Overview This chapter provides solutions to problems usually encountered during the installation and operation of the Wireless Network Access Point. Please refer to the following description to solve your problems. If you can' t find an answer here, please contact your dealer for further advice. Q:My PC can' t locate the Wireless Access Point. How to check the problem ? A:First, please check your PC is set to Infrastructure Mode. Then please make sure the wireless channel used matches the wireless channel on Access Point and the SSID on your PC are same as that of the Wireless Access Point. Because both your PC and the Wireless Access Point must have the same setting for WEP, if WEP is enabled, the key tables must match. Besides that, to see if radio interference is causing a problem, see if connection is possible when close to the Wireless Access Point. [. . . ] That is, the MAC address is assigned as a physical address unique throughout the world. In an Ethernet LAN, the MAC address is used as a base to create a frame for sending and receiving. TCP/IP (Transmission Control Protocol/Internet Protocol) TCP/IP is a protocol equivalent to the network and transport levels of the OSI reference model, and it is defined using RFC. Consequently, different terminals can communicate with each other using TCP/IP. · Normally, TCP/IP includes the application protocols TELNET and FTP. [. . . ]