User manual TRENDNET TEW-410APBPLUS

[. . . ] TEW-410APBplus Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior writing of the publisher. January. 2004 User's Guide 1 Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please input the period of renewal time. The default selection is 300 seconds. User's Guide 9 -WPA RADIUS WPA RADIUS uses an external RADIUS server to perform user authentication. To use WPA RADIUS, enter the IP address of the RADIUS server, the RADIUS Port (default is 1812) and the shared secret from the RADIUS server. WPA Algorithms Radius Server Address RADIUS Server Port RADIUS Shared Key Group Key Renewal Please choose your algorithms method. Please input your RADIUS Server IP address. Please input the Authentication port of your RADIUS server. The default port being used is 1812 The RADIUS server will accept the authentication if both Shared Key matched. Please input the period of renewal time. The default selection is 300 seconds. * Click Apply to save your settings. TEW-410APBplus 4. 2. System AP Password: Changing the password for the AP is as easy as typing the password into the Enter New Password field. Then, type it again into the Re-enter to confirm. * Click the Apply button to save the setting. Use the default password when you first open the configuration pages, after you have configured these settings, you should set a new password for the AP (using the Password screen). This will increase security, protecting the AP from unauthorized changes. Restore Factory Defaults: Click the Yes button to reset all configuration settings to factory default values. Note: Any settings you have saved will be lost when the default settings are restored. Click the No button to disable the Restore Factory Defaults feature. Click the Apply button to save the setting. Backup/Restore Setting: Click Backup to store the Access Point's configuration on your local PC. Click Restore to restore Access Point's configuration from your local PC * Check all the settings and click Apply to save them. User's Guide 11 4. 3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations. AP Client: Please input the MAC Address of the remote AP. In this operating mode, the device will be used as wireless NIC. TEW-410APBplus Important Both units must be selected as AP Repeater mode in order to establish the Wireless link communication. The remote AP MAC address to be filled at this selection should be the MAC address that is displaying at the Operating Mode's web pages AP Repeater: This mode allows the AP to keep the AP function role and at the same time performing a communication with other 802. 11g AP to establish and extend your Wireless Network cover. Please enter the Remote Access Point's MAC address to enable this feature. Wireless Bridge: This mode allows the connection of one or more remote LANs with a central LAN. * Click Apply to save your settings. User's Guide 13 4. 4. Status This screen displays the IEEE 802. 11g AP's current status and settings. [. . . ] On the Firmware Upgrade screen, click the Browse button to find the firmware upgrade file. TEW-410APBplus 5. Click the Upgrade button, and follow the on-screen instructions. Note: Do not power off the AP or press the Reset button while the firmware is being upgraded. User's Guide 21 5. Troubleshooting Basic Functions My Wireless AP will not turn on. [. . . ]