User manual TRENDNET TEW-636APB

[. . . ] TABLE OF CONTENTS CHAPTER 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features of your Wireless Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Physical Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use this when adding or editing a Trusted Station. Delete a Trusted Wireless Station from the list (move to the "Other Stations" list). · · Select an entry (or entries) in the "Trusted Stations" list. Click the " >> " button. Select All Select None Select all of the Stations listed in the "Other Stations" list. De-select any Stations currently selected in the "Other Stations" list. 34 Access Point Setup Edit To change an existing entry in the "Trusted Stations" list, select it and click this button. Select the Station in the "Trusted Station" list. The address will be copied to the "Address" field, and the "Add" button will change to "Update". Edit the address (MAC or physical address) as required. Click "Update" to save your changes. To add a Trusted Station which is not in the "Other Wireless Stations" list, enter the required data and click this button. Clear the Name and Address fields. Add Clear 35 Wireless Access Point User Guide Advanced Settings Clicking the Advanced Settings link on the Wireless menu will result in a screen like the following. Figure 23: Advanced Settings Data - Advanced Settings Screen Options Worldwide Mode (802. 11d) WMM Enable WMM Support Check this to enable WMM (Wi-Fi Multimedia) support in the Access Point. If WMM is also supported by your wireless clients, voice and multimedia traffic will be given a higher priority than other traffic. If enabled, then WMM acknowledgement is disabled. Depending on the environment, disabling acknowledgement may increase throughput slightly. Enable this setting if you wish to use this mode, and your Wireless stations support this mode. No Acknowledgement Parameters Disassociated Timeout This determines how quickly a Wireless Station will be considered "Disassociated" with this AP, when no traffic is received. Enter the preferred setting between 256 and 2346. Normally, this can be left at the default value. Enter the preferred setting between 20 and 1000. Normally, this can be left at the default value. Enter the preferred setting between 256 and 2346. Normally, this can be left at the default value. The "Short" setting takes less time when used in a good environment. 36 Fragmentation Length Beacon Interval RTS/CTS Threshold Preamble Type Access Point Setup Wi-Fi Protected Setup Click WiFi Protected Setup on the Wireless menu to view a screen like the following. Figure 24: WPS PIN Screen Data - WPS PIN Screen WPS PIN Input Enrollee's PIN Change AP Settings Check this and enter the PIN code to the client device. [. . . ] This is desirable because it is impossible to prevent snoopers from receiving any data which is transmitted by your Wireless Stations. But if the data is encrypted, then it is meaningless unless the receiver can decrypt it. If WEP is used, the Wireless Stations and the Wireless Access Point must have the same settings. WPA-PSK Like WEP, data is encrypted before transmission. WPA is more secure than WEP, and should be used if possible. [. . . ]