User manual TRENDNET TEW-638PAP

[. . . ] 1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Devices like Network storage, network enable printers, and gaming consoles can now be wirelessly enable by connect the TEW-638PAP in the AP Client mode. AP Client Mode After selecting the operation mode click on Apply to save the setting at the bottom of the window. Page 26 NETWORK LAN SETTING These are the settings of the LAN (Local Area Network) interface for the Access Point. The Access Point's local network (LAN) settings are configured based on the IP Address and Subnet Mask assigned in this section. The IP address is also used to access this Web-based management interface. LAN Connection Type Choose "Static IP (fixed IP)" if your router does not support DHCP or if for any other reason you need to assign a fixed address to the AP. In this case, you must also configure the following fields. IP Address The IP address of the AP on the local area network. Assign any unused IP address in the range of IP addresses available for the LAN. Subnet Mask The subnet mask of the local area network. Default Gateway The IP address of the router on the local area network. Choose "DHCP (Auto Config)" if your router supports DHCP and you want the router to assign an IP address to the AP. Page 27 WIRELESS The wireless section is used to configure the wireless settings for your Access Point. Note that changes made in this section may also need to be duplicated on wireless clients that you want to connect to your wireless network. To protect your privacy, use the wireless security mode to configure the wireless security features. The Wireless tab provides the following configuration options: Basic, Advanced, MAC Filter, Security, WPS and Station List. Wireless Basic Access Point Page 28 AP Mode Support AP Mode Support allows you to "repeat" a wireless signal from an existing access point. Select the radio button to enable or disable "AP Mode Support". When enabled you have the option of defining the specific access point to repeat off of by entering in the remote access points or wireless router's wireless MAC address into the "AP MAC Addr. You must also configure the TEW-638AP with the same SSID, channel and wireless encryption settings of the remote access point. AP Mode Support enabled Wireless Mode If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate "Only" mode. If you have some devices that use a different transmission mode, choose the appropriate "Mixed" mode. Wireless Modes 802. 11b/g mixed mode (2. 4GHz) - This wireless mode works in the 2. 4GHz frequency range and will allow both wireless b and wireless g client to connect and access the TEW-638PAP at 11Mbps for wireless b, at 54Mbps for wireless g and share access at the same time. Although the wireless b/g operates in the 2. 4GHz frequency, it will allow the use of other 2. 4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. Page 29 802. 11n only (2. 4GHz) - This wireless mode works in the 2. 4GHz frequency range and will only allow the use of wireless n client devices to connect and access the TEW-638PAP up to 300Mbps*. Although the wireless n operates in the 2. 4GHz frequency, this mode will only permit wireless n client devices to work and will exclude any other wireless mode and devices that are not wireless n only. 802. 11b/g/n mixed mode (2. 4GHz) - This wireless mode works in the 2. 4GHz frequency range and will only allow the use of wireless g client devices to connect and access the TEW-638PAP at 11Mbps for wireless b, 54Mbps for wireless g and up to 300Mbps* for wireless n and share access at the same time. [. . . ] Please contact the pointofpurchase for their return policies. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. [. . . ]