User manual TRENDNET TEW-645UB

[. . . ] Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The following lists the main features of your Adapter. Your Adapter can communicate with other IEEE 802. 11n/b/g compliant wireless devices. Wire-free access to networked resources from anywhere beyond the PC with any USB host interface. Support Infrastructure & Ad-Hoc mode Delivers receiving data rate up to 300 Mbps in 11n mode. For 802. 11b/g, date rate dynamically shifts based on signal strength, for maximum availability and reliability of connection. Support both 20MHz & 40MHz bandwidth Support WEP 64/128, WPA, WPA2 encryption Support QoS ­ WMM Multi-path (1x2) design and two PCB antennas built-in design guarantee best transmitting / receiving quality. Support Windows-base wireless LAN GUI Support WPS enable on S/W utility 2. 2 Package Content 802. 11n/b/g WLAN USB2. 0 Adapter USB Cradle Installation and Manual CD Quick Start Guide Warranty/Registration Card 2. 3 System Requirement Pentium class notebook computers with at least one available USB slot Microsoft Windows Vista, XP and 2K CD-ROM drive 2. 4 Wireless Utility & Adapter Hardware Installation NOTE: If you have connected the USB Adapter to your computer, please remove it first. Follow the instructions below to install the USB Adapter and Utility. STEP 1 Insert the Driver and Utility CD into CD drive 11 STEP 2 If your CD Autorun is enabled, the installation procedures will be started. (Otherwise open your CD folder and double-click on the "setup. exe" file) STEP 3 The InstallShield Wizard prepares for installation. STEP 4 The InstallShield Wizard prompts you for confirmation. Click Next on the following menu. 12 STEP 5 In the destination Folder screen you are asked to confirm the Destination Folder for the application software. If you would like, you may change the destination folder to another location. Click Next STEP 6 The wizard is ready to begin installation. Click Install on it. 13 STEP 7 The Install shield Wizard setup for installation. STEP 8 Click Finish to complete the client utility installation. 14 STEP 9 At this moment please insert your USB Adapter to your Laptop through the cradle. After the following window pop up, click Next on the Fund New Hardware Wizard STEP 10 Choose "Install the software automatically" , and click Next. 15 STEP 11 Click Finish to complete the installation. 16 2. 6 Using the Utility to Configure Your Network The following are explanations on how to configure and use the Utility program. After completing the installation procedure, a new icon as shown below will automatically appear in the lower right tray bar. Hold your mouse pointer over the icon, and press the right mouse button to open the Wireless Client Utility. The Wireless Client Utility window as shown below will appear. The user can now use any of the management functions available in the IEEE 802. 11 Wireless Client Utility. 17 2. 6. 1 Link Information Click the Link Information tab to see general information about the program and its operations. The Link Information tab does not require any configuration. 18 The following table describes the items found on the Link Information screen. Wireless Network Status Profile Name SSID Link Status The name of the current selected configuration profile. Set up the configuration name on the Profile tab. Shows whether the station is associated to the wireless network. The type of network the station is connected to. The options include: Displays the wireless mode. 802. 11g, 11b or 11n Shows the currently connected channel. Displays the current transmit rate in Mbps. Displays the BSSID of the wireless network that the wireless adapter is associated to. [. . . ] To remove the utility from the OS, go to Start -> Control Panel Step 2. Step 3. Double-click Add-Remove Programs Select 802. 11n Wireless Client Utility, and click the Remove button 3. 3 Upgrading the Wireless Utility To perform the upgrade, follow the steps below. Download the latest version of the utility from the web site and save the file on your computer. Step 2. Step 4. Follow the steps in Section 2. 2 to remove the current Wireless Utility from your computer. [. . . ]