User manual TRENDNET TEW-MP1U

[. . . ] Table of Contents Chapter 1 Introduction 1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Physical Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Check the wireless and IP settings of the Access Point which your PC is connecting to. Procedure 1. Insert the supplied CD-ROM into your drive. If the setup program does not start automatically, run Autorun. exe in the root folder. On the first screen, shown below, click Setup Wizard. Page 5 Figure 2: Main Screen 3. Click OK to follow the setup procedures: (1) Connect MFP/All-in-one machine to Wireless Print Server. (2) Connect both PC and Wireless Print Server to Router or Hub. (5) Check the LED on the Wireless Print Server. Status LED (Green) should be ON and Error LED (Red) is OFF. · · To use the LAN interface, the LAN cable needs to be inserted BEFORE powering ON. The Wired (LAN) interface should be used for initial configuration. In the default Wireless "Infrastructure" mode, connecting a LAN cable will disable the Wireless interface. · Or click Skip if all the above steps have been done already. Select your Wireless Print Server, then click Next to continue. Figure 3: Wizard Screen 5. If the Access Point does not show up, click the Refresh button. Page 6 Figure 4: Wireless Network Screen 6. If you select the Manually Setting, click Next to move to the Security Setting screen. Figure 5: Security Setting Screen 7. For the Security Setting screen: · · · · Network Type - Select the correct value for your Wireless LAN. SSID - All Wireless stations MUST use the same SSID to communicate with one another. Channel -·If "Automatic" is selected, the Access Point will select the best available channel. Security - There are 4 options for Wireless Security · · · · · · Disable - no data encryption is used. Data is encrypted before transmission, but the encryption system is not very strong. WPA-PSK - data is encrypted using the Wi-Fi Protected Access with Preshared Key standard. WPA is wireless security with far greater protection than WEP. WPA-PSK offers two encryption methods, TKIP and AES, with dynamic encryption keys. WPA2 - this is a further development of WPA-PSK, and offers even greater security. [. . . ] WPA2-PSK - this is a further development of WPA-PSK, and offers even greater security. Wireless Security - WEP If "WEP" is selected, the screen will look like the following example. Figure 13: WEP Screen Security System WEP The 802. 11b standard. Data is encrypted before transmission, but the encryption system is not very strong. Select the appropriate value, as used on your Wireless LAN "Open System" or "Shared Key. " Select the WEP Encryption level: · · 64-bit (sometimes called 40-bit) encryption 128-bit encryption (sometimes called 104 bit encryption) Authentication Key Size This selection also allows you to choose the input type for the keys - Hex or ASCII. Keys · · · Use the radio buttons to select the default key. [. . . ]