User manual TRENDNET TFM-560PCI

[. . . ] I101 V. 90 PCI MODEM USER'S MANUAL 44 Lo ok I101 V. 90/K56flex MODEM USER'SMANUAL TABLE OF CONTENT 1. Comprehensive Modem Installation Instructions 2. 1 2. 2 2. 3 2. 3. 1 2. 3. 2 2. 3. 3 2. 3. 4 2. 3. 5 2. 4 2. 5 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setup Instructions for Windows 98. . . . . . . . . . . 4 Setup Instructions for Windows 95. . . . . . . . . . . 6 Uninstall Modem in Windows 98/ 95. . . . . . . . . . . 9 Setup Instructions for Windows NT4. 0. . . . . . . . . . 10 Uninstall Modem in Windows NT4. 0. . . . . . . . . . . 11 Testing your modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Install Communication Software. . . . . . . . . . . . . . . 12 3. Troubleshooting Appendix 1: Appendix 2: Appendix 3: Appendix 4: Appendix 5: Modem Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 15 AT Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 S-registers Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Result Code Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Government Compliance. . . . . . . . . . . . . . . . . . . . . . . 24 P. 1 I101 V. 90 PCI MODEM USER'S MANUAL 44 Section 1 Contents of Package One V. 90/K56flex PCI bus window modem One telephone cable One CD-ROM disk comprises Communication software, Modem Driver & User's Manual Quick installation guide Please contact the place of purchase if any of the above listed items are missing. Speaker and microphone are additional accessories. [. . . ] Generally, if a connection exists, this command connects the DTE back to the remote modem after an escape (+++). 1 Performs a retrain then enters on-line data mode from the on-line command mode. A2. 2. 3. 7 L[<value>] - Speaker Volume This command sets the speaker volume control according to the parameter supplied. Defined Values <value> Decimal number corresponding to the selected option. 3 High volume. A2. 2. 3. 8 M[<value>] - Speaker Control This command controls speaker on or off according to the supplied parameter. Defined Values <value> Decimal number corresponding to the selected option. 1 Speaker on during call establishment, but off when receiving carrier. 3 Speaker is off when receiving carrier and during dialing, but on during answering. A2. 2. 3. 9 &G[<value>] - Select Guard Tone This command is included for compatibility only and has no effect other than returning an OK result code. Defined Values <value> Decimal number corresponding to the selected option. 0 Included for compatibility only and has no effect other than returning an OK result code. (Default. ) 1 Included for compatibility only and has no effect other than returning an OK result code. 2 Included for compatibility only and has no effect other than returning an OK result code. A2. 2. 3. 10 &P[<value>] - Select Pulse Dial Make/Break Ratio This command determines the make/break ratio used during pulse dialing. It is only effective if the appropriate bit to enable this command is set through the Product Configuration File. If enabled, it will override the make/break ratios in the OEM parameters in the Product Configuration File. The default is country-dependent. P. 26 I101 V. 90 PCI MODEM USER'S MANUAL 44 Defined Values <value> Decimal number corresponding to the selected information. 0 Selects 39%-61% make/break ratio at 10 pulses per second. (Default. ) 1 Selects 33%-67% make/break ratio at 10 pulses per second. 2 Selects 39%-61% make/break ratio at 20 pulses per second. 3 Selects 33%-67% make/break ratio at 20 pulses per second. A2. 2. 3. 11 &V - Display Current Configuration and Stored Profile This command reports the current (active) configuration and the stored (user) profiles. A2. 2. 3. 12 &W - Store Current Configuration This command saves the current (active) configuration (profile), including S-Parameters, in Product Configuration File. The current configuration is comprised of a list of storable parameters illustrated in the &V command. These settings are restored to the active configuration upon receiving an Z command or at power up. A2. 2. 3. 13 *B - Display Blacklisted Numbers This command requests the modem to return a list of blacklisted numbers to the DTE. The format of the response is shown by the example below. Permanently forbidden numbers as defined by country requirements will not appear on this list. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]