User manual TRENDNET TFM-560R

[. . . ] INTRODUCTION This chapter offers an overview of the high speed PC Card FAX/MODEM. It includes: General Description Unpacking Information Hardware Overview What You Need To Use Your Modem General Description This PC Card Fax/Modem is a credit-card-size Type II PCMCIA card that complies with the PCMCIA 2. 1 standards and works with computers that incorporate a compatible interface. It is Bell, ITU-T (formerly CCITT) compliant and Hayes AT command compatible, allowing it to be used worldwide with today's popular communication software programs. You will be able to send and receive faxes to/from any Group 3 compatible fax machine. [. . . ] Be sure to update your software COM port setting as well. C: The Interrupt that the modem is using may be the same as which another card is using. C: Both the modem and the software have the echo turned on. S: Since only one needs the echo, turn off the echo feature of the software. C: The remote modem is echoing your typed characters. Then turn off the echo feature of the software. 1-14 P: No text appears on the screen when in data mode. C: The remote modem is not echoing your typed characters. Then turn on the echo feature of the software. C: Your software may not be set to use full duplex or the remote modem may not be set to use full duplex either. C: The remote modem may be waiting for you to type commands before it replies. P: No text appears on the screen when in command mode. S: If you can't see the characters you are typing, type ATE1 then press Enter. P: The modem does not dial the phone number after you execute the dialing AT command. C: If you are using touch tone dialing for the phone line that requires rotary pulses dialing, it may not work. P: When your communications software drives the modem to make dialing, the PC Card does not take any action. C: Make sure the ATDT dialing prefix is correctly set in the software you are using. C: Make sure the software and modem are set to consistent COM port. C: The modem may not hang up the last call. S: Switch to command mode and type ATH then press Enter. P: The modem can connect to some modems, but not others. C: The remote modem may not support data compression or error correction. [. . . ] OFF) Manufacturer default Options * 7. 2 Result Code Options Result Code Options Table ATV0 ATV1 X0 X1 X2 X3 X4 X7 1-24 0 1 2 3 4 5 6 7 8 10 11 12 13 14 18 24 25 28 40 55 56 57 58 59 60 70 71 72 73 74 75 76 77 78 79 80 81 82 86 87 88 89 90 @ # OK CONNECT RING NO CARRIER ERROR CONNECT 1200 EC* NO DIAL TONE BUSY NO ANSWER CONNECT 2400 EC * CONNECT 4800 EC * CONNECT 9600 EC * CONNECT 14400 EC * CONNECT 19200 EC * CONNECT 57600 EC * CONNECT 7200 EC * CONNECT 12000 EC * CONNECT 38400 EC * CONNECT 300 EC * CONNECT 21600 EC * CONNECT 24000 EC * CONNECT 26400 EC * CONNECT 28800 EC * CONNECT 31200 EC * CONNECT 33600 EC * CONNECT 32000 EC * CONNECT 34000 EC * CONNECT 36000 EC * CONNECT 38000 EC * CONNECT 40000 EC * CONNECT 42000 EC * CONNECT 44000 EC * CONNECT 46000 EC * CONNECT 48000 EC * CONNECT 50000 EC * CONNECT 52000 EC * CONNECT 54000 EC * CONNECT 56000 EC * CONNECT 16800 EC * CONNECT 115200 EC * DELAYED ** BLACKLISTED ** BLACKLIS FULL ** @ @ @ @ @ # @ % # # % @ # # # # # # # # # # # # # # # # # # # # % @ @ @ @ # @ % # # % @ # # # # # # # # # # # # # # # # # # # # % @ @ @ # @ % # # % @ # # # # # # # # # # # # # # # # # # # # % @ @ @ @ # @ % # # % @ # # # # # # # # # # # # # # # # # # # # % DTE/DCE speed DCE speed (line speed) 1-25 % * ** DTE speed EC only appears when the Extended Result Code options are enabled For Blacklisting function enabled countries only Extended Result Code Options Table ATV0 5 5 10 10 11 11 12 12 13 13 14 14 18 18 24 24 25 25 28 28 40 40 55 55 56 56 57 57 58 58 59 59 60 60 70 70 71 71 72 ATV1 CONNECT 1200 CONNECT 1200 EC* CONNECT 2400 CONNECT 2400 EC * CONNECT 4800 CONNECT 4800 EC * CONNECT 9600 CONNECT 9600 EC * CONNECT 14400 CONNECT 14400 EC * CONNECT 19200 CONNECT 19200 EC * CONNECT 57600 CONNECT 57600 EC * CONNECT 7200 CONNECT 7200 EC * CONNECT 12000 CONNECT 12000 EC * CONNECT 38400 CONNECT 38400 EC * CONNECT 300 CONNECT 300 EC * CONNECT 21600 CONNECT 21600 EC * CONNECT 24000 CONNECT 24000 EC * CONNECT 26400 CONNECT 26400 EC * CONNECT 28800 CONNECT 28800 EC * CONNECT 31200 CONNECT 31200 EC* CONNECT 33600 CONNECT 33600 EC * CONNECT 32000 CONNECT 32000 EC* CONNECT 34000 CONNECT 34000 EC* CONNECT 36000 W0 W1 W2 W2\V0 1-26 * 72 CONNECT 36000 EC* 73 CONNECT 38000 73 CONNECT 38000 EC* 74 CONNECT 40000 74 CONNECT 40000 EC* 75 CONNECT 42000 75 CONNECT 42000 EC* 76 CONNECT 44000 76 CONNECT 44000 EC* 77 CONNECT 46000 77 CONNECT 46000 EC* 78 CONNECT 48000 78 CONNECT 48000 EC* 79 CONNECT 50000 79 CONNECT 50000 EC* 80 CONNECT 52000 80 CONNECT 52000 EC* 81 CONNECT 54000 81 CONNECT 54000 EC* 82 CONNECT 56000 82 CONNECT 56000 EC* 86 CONNECT 16800 86 CONNECT 16800 EC * 87 CONNECT 115200 87 CONNECT 115200 EC * EC is replaced by one of the following symbols. V. 42bis V. 42 error control and V. 42bis data compression V. 42 V. 42 error control only MNP5 MNP 4 error control and MNP 5 data compression MNP4 MNP 4 error control only NoEC No error control and data control protocols 1-27 APPENDIX D: S-REGISTERS S-Registers, "ATSn=x" Register S0= Dec. 0 - 255 Function & Description Default Set the number of the rings required 000 before the modem automatically answers a call. Set "S0=0" to disable auto-answer mode Count the incoming rings and store the 000 value to this register. [. . . ]