User manual TRENDNET TFM-560U

[. . . ] E500 V. 90 USB MODEM USER'S MANUAL 38 Lo ok E500 V. 90 USB MODEM USER'S MANUAL TABLE OF CONTENT 1. Comprehensive Modem Installation Instructions 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Setup Instructions for Windows 98. . . . . . . . . . . 3 Testing your modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Monitor Application of USB modem. . . . . . . . . . . . . 7 Install Communication Software. . . . . . . . . . . . . . . 9 3. Troubleshooting Appendix 1: Modem Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Appendix 2: ModioTM AT Command Sets. . . . . . . . . . . . . . . . . . . . . . 12 Appendix 3: Government Compliance notices. . . . . . . . . . . . . . . . 37 P. 1 E500 V. 90 USB MODEM USER'S MANUAL 38 Section 1 Contents of Package - One V. 90 USB Modem - Quick installation guide - One CD-ROM disk comprises Communication software, Modem Driver & User's Manual - One Telephone Cable - One USB Cable Please contact the place of purchase if any of the above listed items are missing. Section 2 Section 2. 1 Comprehensive Modem Installation Instructions System Requirements The modem operates on a personal computer equipped with the following: - Pentium R 166MMX or faster CPU ( 200 MHz recommended ) - 16 MB RAM - USB port - Windows 98 or Windows NT 5. 0 operating system Section 2. 2 Hardware Installation Please refer to Fig. 2 - 1 and proceed to following steps for how to connect your modem to the computer and with USB port and telephone wire. Phone Jack FIGURE 2-1 V. 90 USB modem diagram USB Jack 1. [. . . ] M0 M1 M2 M3 Speaker always OFF Speaker ON from start of dialing until receiving carrier (Default) Speaker always ON Speaker OFF from end of dialing until receiving carrier P. 15 E500 V. 90 USB MODEM USER'S MANUAL 38 Result codes: OK Error n=0-3 Otherwise Related S-Reg: S29 Nn Automode control Enable/Disable Automode detection. A subsequent handshake will be conducted according to the contents of S32. A subsequent handshake will be conducted according to the Automode algorithm. (Default) n=0 or 1 Otherwise Result codes: OK Error Related S-Reg: S31 On Returns to on-line data mode This command is normally used to connect the DTE back after an escape (+++) has been issued. O0 O1 OK Error Return to on-line data mode. Return to on-line data mode, retrain first. n=0-1 Otherwise Result codes: P Pulse dialing Forces pulse dialing. This command holds until the next T dial modifier or T command is received. The modem will go off hook and attempt to answer an incoming call. Upon successful completion of handshake, the modem will go on-line in answer mode. Related S-Reg: S16 Q Quiet result codes control Q0 Q1 OK Error Enable sending result codes to DTE. (Default) Disable sending result codes to DTE. n=0 or 1 Otherwise Result codes: Related S-Reg: S14 P. 16 E500 V. 90 USB MODEM USER'S MANUAL 38 S Read/Write S-Register This command has a few derivatives: Sn=v Sn?Sets the value v (decimal) to S-register n (v=0-255) Displays the value of S-register in decimal format (3 digits) Note: Some registers are read-only Result codes: OK Error All parameters valid Invalid S register or value. Trying to write to a read-only register T Tone dialing Forces tone dialing. This command holds until the next T dial modifier or T command is received. This command changes S14 to reflect the current dialing mode. Related S-Reg: S16 Vn Verbose/Numeric result codes Select the time of result messages sent to the DTE. For a list of result codes and verbal messages see X command. V0 V1 OK Error Short form (numeric) result codes to be sent to DTE. Long form (verbose) result codes to be sent to DTE. (Default) n=0 or 1 otherwise Result codes: Related S-Reg: S15 Xn Extended result codes Select the subset of result codes to be used by the modem to the DTE. If the modem is in fax mode (+FCLASS=1), the only message sent to indicate connection is "CONNECT" without a speed indication. X0 X1 X2 X3 X4 Notes: W, @ dial modifiers are ignored in X1, X2 S6 (Wait before dial) is ignored in X2, X4 if no W is specified in dial string S6 is set to 0 means a blind call Supported messages: OK, CONNECT, RING, NO CARRIER and ERROR, Blind call enabled. [. . . ] On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify in advance. [. . . ]