User manual TRENDNET TPL-407E2K

[. . . ] 6 CONFIGURATION UTILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CONFIGURATION UTILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 INSTALL CONFIGURATION UTILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 USING THE POWERLINE AV UTILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 10 Network ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 About. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 INTRODUCTION Thanks for purchasing of the 200M Powerline AV to Fast Ethernet Adapter. This Adapter will allow your Ethernet device to connect to other Ethernet devices through AC power line. About the 200M Powerline AV to Fast Ethernet Adapter The 200M Powerline AV to Fast Ethernet Adapter allows user to connect with other Ethernet enabled devices through AC power line at home or office. The 200M Powerline AV to Fast Ethernet Adapter is designed to provide the Plug-and-Play installation, user just connected the Ethernet cable on the Adapter and Ethernet enabled device and pluged the Adapter to AC outlet. Terms/Usage In this guide, the term "the TPL-407E2K" refers to the 200M Powerline AV to Fast Ethernet Adapter. Product Features Compliant with 200M Powerline AV specifications Compliant with IEEE 802. 3 10BASE-T Ethernet, IEEE 802. 3u 100BASE-TX specification ANSI/IEEE 802. 3 Auto-negotiation and Auto MDI and MDIX Powerline speed up to 200Mbps 3 LED indicators for Power, Powerline Activity and Ethernet port Link/Activity Support quickly setup button 1 IDENTIFYING EXTERNAL COMPONENTS This section identifies all the major external components of the 200M Powerline AV to Fast Ethernet Adapter. LED Indicators LED Display On Power Off Blinking On Powerline Off Blinking On Ethernet Off Blinking Status description The TPL-407E2K is connected to the AC power line and operation normal. The TPL-407E2K is not connected to the AC power line. The TPL-407E2K is goes to firmware upgrade or on pairing. The TPL-407E2K is the PowerLine addresser. The PCL is not join to PowerLine group The TPL-407E2K is the PowerLine joiner. If a packet has both VLAN and TOS in it, VLAN will override TOS. Default CAP The `Default CAP' group allows for default priority mapping of packets that do not have a VLAN or TOS bit. Settings are available for Unicast (directed to a host). · IGMP - (default CAP 3) - sets the channel access priority for IGMP frames - these are the group management frames, not the stream data · Unicast - (default CAP 1) - sets the default channel access priority for unicast frames not matching any other classification or mapping. · IGMP managed Multicast Stream (default CAP 2) - sets the default channel access priority for stream data belonging to a snooped IGMP multicast group. · Multicast/Broadcast - sets the default CAP1 for multicast frames not in a snooped group and for broadcast frames. Device Selection Select the device from the drop down list and configure the device selected. 10 11 Reset to default Press the Reset to default button to restore the factory default QoS setting. Save changes Press the Save changes button to save and execute the modified QoS setting. Network ID This Network ID window is used to set or change the network group id. Setting the local device Network ID , If the Device Selection is selected to local device enter the network ID in Network ID filed then click Save changes button to sets the entered Network ID. , If the Device Selection is selected to remote device enter the network ID in Network ID filed and enter the remote device access key in DAK password field then click Save changes button to sets the entered Network ID. (The DAK password is show on each TPL-407E2K's device label). Reset to Default Press the Reset to Default button to restore the factory default network id setting for "TRENDnet". Device Selection Select the device form drop down list will be configure. 12 13 Upgrade Device Selection Select the device form drop down list will be configure. [. . . ] TPL-407E2K ­ 3 years If a product does not operate as warranted above during the applicable warranty period, TRENDnet shall, at its option and expense, repair the defective product or deliver to customer an equivalent product to replace the defective item. All products that are replaced will become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. [. . . ]