User manual TRENDNET TV-IP110

[. . . ] PREFACE Thank you for purchasing the TV-IP110/TV-IP110W Wire/Wireless Internet Camera Server, a powerful and high-quality image network camera. The camera can be installed as a standalone system within your application environment easily and quickly, and supports remote management function so that you can access and control it using a Web browser on your PC. This guide will provide you more information of instruction and illustrations on how to use your camera, which includes: Chapter 1 Introduction to Your Camera describes the features of the camera. You will also know the components and functions of the camera. [. . . ] Click Delete to remove the selected time period. - Start/End Time: Enter the start and end time and then click Add to assign a time period within in the selected weekday. - 48 - Event Configuration >> Motion Detect Trigger Select the Enable option to enable the trigger function of the camera, so that you can send captured images within the detecting area to the FTP server and email receiver. You have to configure corresponding settings, such as FTP server and email server, to enable this feature. - Schedule Profile: Select a schedule profile from the pull-down list. - Action: Select the destination that the captured images will be sent to: Send Email, or FTP Upload. Event Configuration >> Schedule Trigger - 49 - You can separately configure the schedule for trigger function of the camera by Email or FTP. Select the Enable option on each item, and then select a Schedule Profile from the pull-down list and set the Interval time. - 50 - 4. 9 Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration, and upgrade the firmware for the camera. - 51 - Factory Reset Click Reset to restore all factory default settings for the camera. System Reboot Click Reboot to restart the camera just like turning the device off and on. The camera configuration will be retained after rebooting. Configuration You can save your camera configuration as a backup file on your computer. Whenever you want to resume the original settings, you can restore them by retrieving the backup file. - Backup: Click Get the backup file to save the current configuration of the camera. - Restore: Click Browse to locate the backup file and then click Restore. Update Firmware This item displays the current firmware version. You can upgrade the firmware for your camera once you obtained a latest version of firmware. - Select the firmware: Click Browse to locate the backup file (xxx. pck) and then click Update. Factory reset and IP Setup are required after firmware update. NOTE Make sure to keep the camera connected to the power source during the process of upgrading firmware. Otherwise, the camera might be damaged because of failure of upgrading firmware. - 52 - 4. 10 Information The Information menu displays the current configuration and events log of the camera. Device Info Display the Basic, Video, Network, and Wireless settings of the camera. System Log The Logs table displays the events log recorded by the system. - 53 - CHAPTER 5 SECURVIEWTM SOFTWARE This Chapter describes detail instructions on operating SecurViewTM software, a useful friendly application for ease of control and navigation requirement. 5. 1 1. INSTALLATION Insert the Installation CD-ROM into your computer's CD-ROM drive to initiate the Auto-Run program. 2. Click the SecurView from the Auto-Run menu screen. - 54 - NOTE To use SecurViewTM, you must have Microsoft . NET Framework 2. 0 installed in the computer. The setup wizard will detect it and, if the program is not installed yet, ask you to install it during the process of installing SecurViewTM. - 55 - 3. Then SecurView Setup Wizard will appear. Click "Next" when the Welcome to the SecurView Setup Wizard appears. 4. Click "Browse" to choose the desired destination location. By default, the destination location is C:\Program Files\TRENDnet\SecurView. Then Click "Next". - 56 - 5. Click "Next" to confirm the SecurView software to be installed to the computer. - 57 - 6. When the Installation Complete window appears, click "Close". 7. After installing the IPSetup utility, the application is automatically installed to your computer, and creates a folder in " Start \Program\TRENDnet\SecurView". - 58 - 5. 2 1. USING INSTALLATION To launch the program, click Start > Program > TRENDnet > SecurView, and then click SecruViewTM. The main screen will appear as below. NOTE Please set the resolution to 1024x768 or above on your computer while using SecurViewTM; otherwise, the displayed main screen may be distorted. Item features The following describes the function of each item on the main screen: CONTROLS Panel - 59 - - SETTING: Click to enter the Setting screen of SecurViewTM. [. . . ] A wide-area network consists of groups of interconnected computers that are separated by a wide distance and communicate with each other via common carrier telecommunication techniques. WEP is widely used as the basic security protocol in Wi-Fi networks, which secures data transmissions using 64-bit or 128-bit encryption. Windows is a graphical user interface for workstations that use DOS. WPA (Wi-Fi Protected Access) is used to improve the security of Wi-Fi networks, replacing the current WEP standard. [. . . ]