User manual TRICITY 160RC (ONYX)

[. . . ] For general enquiries concerning your Electrolux appliance or for further information, visit our website at http://www. electrolux. co. uk Customer Care Department Electrolux 55 - 77 High Street Slough Berkshire SL1 1DZ Tel: *Calls to this number may be recorded for training purposes. 08705 727727* To register ownership, please ensure you complete and return the guarantee card supplied with the appliance. For the User Important Safety Information For the Installer Technical Information Electrical Connections Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Fitting the Wall Brackets Fitting the Canopy Hood Venting Recirculation Fitting the Chimney Stack Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove/Replace Charcoal Filter Changing the Halogen Light Something Not Working Service and Spare Parts Guarantee Conditions Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book Safety instructions Step by step instructions 3 IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation · Any installation work must be undertaken by a qualified electrician or a competent person. · This hood must be installed in accordance with the installation instructions and all measurements must be adhered to. [. . . ] Remove the light bulb by unscrewing it anticlockwise. Insert the new light bulb into the lighting support and screw it clockwise taking care not to overtighten the light bulb. If one of the light bulbs has failed to function check that the lamps is fully screwed into the lighting support. If lamp failure has occurred then it should be replaced with a 40W clear cylindrical lamp with an E14 screw cap. Replacement filters and light bulbs can be obtained from your local Service Force Centre. 8 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · Make sure the switch is in the `ON' position. · The fan speed is set high enough for the task · The grease filter is clean. · The kitchen is adequately vented to allow the entry of fresh air. · If set up for recirculation, check that the charcoal filter is still effective. · If set up for extraction, check that the ducting and outlets are not blocked. · The safety cut-out device has been tripped. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer's installation instructions. A clearance height of 650mm (25 1/2 ") is required when installed above a built-in electric hob, or 700mm (27 1/2 ") when installed above a built-in gas hob. A clearance height of 685mm (27") is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ") when installed above a slot-in gas cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm. If the height of the wall cabinet is less than 450mm, a gap of 50mm must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. The hood can be installed above these heights but for optimum performance it should be installed at the distances quoted for the appropriate heat source. [. . . ] When the cooker hood is ducted to the outside the charcoal filter must be removed. Recirculation The cooker hood is supplied specified for use in the recirculation mode, with the charcoal filter fitted. In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney. To assemble the recirculation duct, place the recirculation outlet connection item 15 into the support item 7. 3. Insert the extension ducts item 14. 1 into either side of the recirculation outlet item 15 ensuring the connections are vertically and horizontally aligned with the outlets in the chimney. [. . . ]