User manual TRICITY BL602W

[. . . ] 2222 268-04 BL 602 W CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 3 4 5 5 5 6 7 7 8 11 12 12 13 14 14 15 15 15 15 16 17 18 Conservation . . Before using . The electrical connections . . Door reversibility Fitting a decorative door panel. [. . . ] Place the appliance in the position where it is to be built in (Fig. The appliance is fitted with adjustable feet; screw the front and rear feet in or out to adjust the height of the appliance to that of the recess. Keeping the appliance central in the recess, slide it in until its back touches the wall. With a tape measure (or similar instrument), measure distance (A) between the top edge of the door and the top edge of the decorative panel, placing it next to the recess. Fig. 8) into their locations in the door and screw them in. Fig. 8 B D532 Hook the decorative panel onto the top part of the door, inserting the pins (B) (on the door) into the elongated holes (1) (in the top bracket fitted to the panel) (Fig. Insert the securing screws (C) through elongated holes (2) and fix the panel without tightening the screws (Fig. 9 A = = 1 B C D467 Lay the panel face down (Fig. Position the top bracket on the panel, making sure that there is an equal distance between it and the sides and that its distance from the top edge is equal to distance (A) less 1 cm. Secure the bracket with the screws supplied. Take care not to damage the front face of the panel whilst working. Fig. 7 2 D533 = = A -1cm D468 8 Once the top of the panel has been correctly positioned, fix it through the holes in the bottom bracket, without tightening the screws (Fig. 10 Once the door has ben correctly aligned, tighten the holding nuts on the fixing brackets and attach the appliance to the adjacent units and the bottom of the work surface (Fig. 12 D471 Check the position again by slackening the screws and pins then, once the best position has been obtained, fully tighten all the fixings. Cover the visible part of the top bracket on the panel with plastic cover (D), inserting it in the locations provided in the bracket. Fig. 11 If the appliance has been fitted into a space 820 mm high and the maximum height of the base plate is 100 mm, fit the front cover plate by pushing the two vertical lugs into the rectangular holes on the bottom side of the ventilation duct until they click. The plate can be adjusted backwards or forwards in the holes (Fig. The following tips should help you to ensure that the food in your home is in as perfect condition as possible. Keep the time between buying chilled food and placing it in your fridge as short as possible. Tests showed that the temperature of 1 litre of orange juice rose to 22°C in an hour between the supermarket and home. It then took 11 hours to get down to 7°C in the refrigerator. Keep the refrigerator door closed as much as possible. [. . . ] Original spare parts can be purchased from Tricity Bendix Service Centres. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for any in-guarantee service calls. 16 PEACE OF MIND FOR TWENTYFOUR MONTHS Guarantee conditions We, Tricity Bendix, undertake that if, within twentyfour months of the date of the purchase, this Tricity Bendix appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. [. . . ]