User manual TRICITY BL603W

[. . . ] 2222 268-05 BL 603 W This document was created with FrameMaker 4. 0. 4 CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 3 4 4 4 4 5 5 6 6 8 9 9 9 10 10 11 11 11 11 12 13 14 Conservation . . Before using . . . The electrical connections . . Door reversibility Fitting a decorative door panel. [. . . ] Remove and refit the other hinge on the upper part of the appliance on the opposite side. Fig. 5 A = = With a tape measure (or similar instrument), measu re d i s t a n c e ( A ) between the top edge of the door and the top edge of the decorative panel, placing it next to the recess. Fig. 7 D467 Fix the two front s c re w s i n t o t h e upper and lower hinges (Fig. 5). D510 Finally, check the alignment of the door and make sure it closes properly. After having reversed the opening direction of the door, discard the original plastic insert removed and fit the insert supplied with the appliance on the opposite side. Lay the panel face down (Fig. Position the top bracket on the panel, mak= ing sure that there is an equal distance between it = A and the sides and -1cm that its distance from the top edge D468 is equal to distance (A) less 1 cm. Secure the bracket with the screws supplied. Take care not to damage the front face of the panel whilst working. Fig. 8 B Insert the adjusting pins (B-Fig. 8) into their locations in the door and screw them in. D532 6 Fig. 13 1 B C D533 2 Hook the decorative panel onto the top part of the door, inserting the pins (B) (on the door) into the elongated holes (1) (in the top bracket fitted to the panel) (Fig. 9). Insert the securing screws (C) through elongated holes (2) and fix the panel without tightening the screws (Fig. 10 If the appliance has been fitted into a space 820 mm high and the maximum height of the 170 base plate is 100 220 mm, fit the front cover plate by 600 pushing the two 135 185 vertical lugs into D518 t h e re c t a n g u l a r holes on the bottom side of the ventilation duct until they click. The plate can be adjusted backwards or forwards in the holes (Fig. 13). 820 870 Once the top of the panel has been c o r re c t l y p o s i t i o n e d , fix i t through the holes in the bottom bracket, without tightening the screws (Fig. 14 820 870 100 150 20÷ 80 Fig. 11 D519 If the base plate is between 100 and 135 mm high, cut it as shown in Fig. If the base plate is between 135 and 170 mm high, cut it as shown in Fig. 15 Check the position again by slackening the screws and pins then, once the best position has been obtained, fully tighten all the fixings. This together with the changes in shopping habits to a once-a-week shop, mean that safe handling and storage of food is even more important than ever. The following tips should help you to ensure that the food in your home is in as perfect condition as possible. Keep the time between buying chilled food and placing it in your fridge as short as possible. Tests showed that the temperature of 1 litre of orange juice rose to 22°C in an hour between the supermarket and home. [. . . ] Original spare parts can be purchased from Tricity Bendix Service Centres. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for any in-guarantee service calls. 12 PEACE OF MIND FOR TWENTYFOUR MONTHS Guarantee conditions We, Tricity Bendix, undertake that if, within twentyfour months of the date of the purchase, this Tricity Bendix appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. [. . . ]